View Full Version : Hydro rudders
Fiat48
03-20-2005, 11:25 AM
Who makes them? Know of 2 Sangers with outboard steeering that need new rudders.
Sangster
03-20-2005, 12:06 PM
Mike's Marine..... Dixon,Ca
Ph# 707-678-4839
Ask for Greg
Fiat48
03-20-2005, 01:53 PM
Thanks! I believe both of the guys have 1/2" thick rudders and want the best available. Both are now alcohol boats. Is that 5/8 thick?
Sangster
03-20-2005, 02:14 PM
I would go 5/8"... :wink:
blue boat
03-20-2005, 04:55 PM
hey fiat 48 ,you might want to try a place out of so cal called barber welding. they make all the struts & rudders for any application.
Fiat48
03-20-2005, 05:26 PM
Thank you. Heard that name before on struts. Anybody got a phone number?
EXTREMEBOATS
03-20-2005, 06:16 PM
Another place to try is Bergeron Engineering in Mesa. The number is 480-834-1531. They will make anything you want! :D
Big Boys Toy PE857
03-20-2005, 06:43 PM
I used Barber welding when I switched from 1" to 1 1/8". Very nice job and timely fashion. Got strut and propshaft. $$$ ouch!
wsuwrhr
03-20-2005, 07:07 PM
Doesn't Schiada96 make underwater gear too?
Brian
superdave013
03-20-2005, 07:09 PM
you can buy it from who ever but the chances are high that it's made at Barber anyway.
Doug Barber 562 928 2570
superdave013
03-20-2005, 07:11 PM
Doesn't Schiada96 make underwater gear too?
Brian
Now schiada96 is the exception to my above post. I know for a fact that he makes everything he sells. Nice stuff too!
BOAT ANCHOR
03-21-2005, 09:39 AM
Who makes them? Know of 2 Sangers with outboard steeering that need new rudders.
James Brendel Racing, Dixon, CA. (925) 325-4967
78Eliminator
03-21-2005, 09:13 PM
But is a 1/2" rudder in a BAH unsafe? Is it illegal with NJBA or IHBA?
BUSBY
03-22-2005, 05:38 PM
The following is from the NJBA rulebook on what is legal for Top Alcohol Hydro, you'll see that 1/2" is the MINIMUM. I would call Ron Braaksma at
909-866-3298 ... he'll send you in the right direction.
TOP ALCOHOL HYDRO - TAH GENERAL
1. Fuel System Mechanized fuel system allowed. The injection system cannot be controlled by exhaust gasses.
2. Fuel Blown Methanol. Unblown Nitro-methane, no percentage limit.
3. Clutch, Flywheel and Bellhousing All boats utilizing a clutch must have a steel hydroformed bellhousing. All boats must have a 360-degree flywheel cover.
4. Neutral Device A devise to allow engagement and disengagement at will of the propulsion device while the engine is running.
5. Prop Shaft The minimum prop shaft diameter through the back of the strut is 1-1/8.
6. Rudder Minimum 1/2 thickness of the clamshell.
ENGINE
1. Any internal combustion automotive type engine permitted. No dual engine set-ups allowed. Maximum 565 cubic inch and 4 valves per cylinder.
2. Supercharger Required roots-type maximum size 14-71, 19 case length, 11-1/4 case width, maximum rotor cavity diameter is 5.840. Helix is restricted to maximum rotor spiral of 6.5 degrees per inch of length. Maximum overdrive 70%.
3. Screw-type superchargers are not allowed.
BB
78Eliminator
03-22-2005, 09:27 PM
Thanks Busby.
BUSBY
03-22-2005, 10:58 PM
no prob ...
BB
P-Money
03-23-2005, 06:12 AM
I've got 2 outboard rudders that I'd like to get rid of. Both are 1/2" thick. PM me with an offer if interested. Here's the longer of the two:
http://www2.***boat.com/image_center/data/520/540DSC00596.JPG
http://www2.***boat.com/image_center/data/520/540DSC00597.JPG
Heres the other (rudder for sale ONLY, unless you want the whole boat :) ):
http://www2.***boat.com/image_center/data/500/540Z10.JPG
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.