4 Bolt SPAM

[obnoxious001]

I have a 454 4 bolt shortblock, apart for inspection $400. The thing was left without the heads on, got rusty, and the owner opted to get an assembled short block to save time. This one is standard bore, should be able to stay at .030 as I was able to remove pistons without dynamite. Crank is cast, already at .010, with stock 3/8" rods and stock pistons. Conveniently located in Southern California.
agt001@aol.com

[steveo143]

please call me @ 714 579-7857 or 714 883-1715 about this motor.
Steve Peterson

[obnoxious001]

still for sale,, anybody need a block?

[obnoxious001]

Still keep tripping over this 4 bolt block, some one must need one, still at standard bore.

[slotracer]

any pictures of it?
pat(slotracer) :)

[obnoxious001]

any pictures of it?
pat(slotracer) :)
No,, I can supply photos if you like, but it is just your average dirty 4 bolt block. The rust is not bad, should clean up fine at .030, based on my experiences.
You can email me directly at agt001@aol.com

[travis hathaway]

I am interested; however, I only need the block and would have to have a trucker buddy of mine to bring it to N.C. What is the casting #. TRAV :clover:

[BLOWN88FRESNO MINI]

I also have a 454 4 bolt for sale
bored .060 over all maching done 2 1/2 years ago, now needs a quick hone, also have forged pistons (press fit) all 500.00
located in Fresno if anybody interested
call 559-352-1309

[BLOWN88FRESNO MINI]

I also have a 454 4 bolt for sale
bored .060 over all maching done 2 1/2 years ago, now needs a quick hone, also have forged pistons (press fit) all 500.00
located in Fresno if anybody interested
call 559-352-1309
Sorry I dont have the Forged pistons after all. but the block is still here!

[sneed]

[QUOTE=obnoxious001]I have a 454 4 bolt shortblock, apart for inspection $400. The thing was left without the heads on, got rusty, and the owner opted to get an assembled short block to save time. This one is standard bore, should be able to stay at .030 as I was able to remove pistons without dynamite. Crank is cast, already at .010, with stock 3/8" rods and stock pistons. Conveniently located in Southern California.
agt001@aol.com[/QUOTE
Do you still have this eng for sale?

[obnoxious001]

I still keep tripping over the thing, someone come and pick it up!
[QUOTE=obnoxious001]I have a 454 4 bolt shortblock, apart for inspection $400. The thing was left without the heads on, got rusty, and the owner opted to get an assembled short block to save time. This one is standard bore, should be able to stay at .030 as I was able to remove pistons without dynamite. Crank is cast, already at .010, with stock 3/8" rods and stock pistons. Conveniently located in Southern California.
agt001@aol.com[/QUOTE
Do you still have this eng for sale?

[victorfb]

you shouldnt have that layin around like that, you can get hurt. let me come take it out of there for ya and i wont even charge you a dumping fee. lol :hammer2:

[JETEATER]

Is the block a two peace or a one peace seal

[obnoxious001]

Is the block a two peace or a one peace seal
It is a Gen 4, 2 piece seal block. Crank and rods are nothing special, but a standard bore 4 bolt block is worth $400 by itself.