WANTED:::: 15 X 30P set of cleavers

[the_gray_goose]

Anyone out there have a good set ( RH & LH ) of 15 X 28 pitch 3 or 4 blade clevers they would like to sell? must fit 300x's

[TOBTEK]

is be calling DREW at BoatMasters...he's the connection for Props!

[mbrown2]

Check scream and fly and offshore only....just got a matching set up 32x14.5 3 blade Mazco cleavers on Offshore Only...excellent shape for $700....little too big ...able to get on plane pretty quick, but only getting about 6K RPM's fully loaded with 4 people 2 ice chests and full of fuel..may have to lab them.

[Kilrtoy]

What are you running now....

[BoatFloating]

What are you running now....
He's running 30p 15's 4B :)

[TOBTEK]

Check scream and fly and offshore only....just got a matching set up 32x14.5 3 blade Mazco cleavers on Offshore Only...excellent shape for $700....little too big ...able to get on plane pretty quick, but only getting about 6K RPM's fully loaded with 4 people 2 ice chests and full of fuel..may have to lab them.
Have any of you "TWIN" guys ran smaller 28" props? how much top would you lose by going from a 30 or 32 down to a 28?

[BoatFloating]

Have any of you "TWIN" guys ran smaller 28" props? how much top would you lose by going from a 30 or 32 down to a 28?
I run 28p 3 blades 14.50 but my taco wagon doesn't know speed. I want Gray Goose to try my props. I think it would be a rocket on the top end with the 3B instead of 4B...

[mbrown2]

Have any of you "TWIN" guys ran smaller 28" props? how much top would you lose by going from a 30 or 32 down to a 28?
You would think it should be a rocket ship with smaller props....I run 28" 4 blades and they have good acceleration (non labbed), but can barely hit 98 with them....I would like to run the 32 with lighter load and see, but the most consistent number I have seen is 105 with the 30"'s 3 blade labbed...Also, the 3 blade throw some cool roosters....and I have not noticed acceleration did too bad with 30's or 32's..
I would like to get a set of 28 3 blades and another 30" 3 blade since I lost a blade on one of my props.

[BoatFloating]

You would think it should be a rocket ship with smaller props....I run 28" 4 blades and they have good acceleration (non labbed), but can barely hit 98 with them....I would like to run the 32 with lighter load and see, but the most consistent number I have seen is 105 with the 30"'s 3 blade labbed...Also, the 3 blade throw some cool roosters....and I have not noticed acceleration did too bad with 30's or 32's..
I would like to get a set of 28 3 blades and another 30" 3 blade since I lost a blade on one of my props.
Daren heard that if you run motors up higher then you wanna go with 15's??? Have you heard this????

[mbrown2]

Daren heard that if you run motors up higher then you wanna go with 15's??? Have you heard this????
I have not heard that, but my 4 blade 28's are 15's....I get pretty good pressure with the 14.5 or 15's...15's are a bigger wheel to turn...

[BoatFloating]

I have not heard that, but my 4 blade 28's are 15's....I get pretty good pressure with the 14.5 or 15's...15's are a bigger wheel to turn...
I think the bigger wheel you have more prop in the water if the motors are higher. I know your props all too well.....
:hammer2:

[the_gray_goose]

Hey all,
Been out of town for a while. thanks for the info here.
The reason for the prop search is I cracked one of the labbed 4 blade 15X30's I had on the boat. Sent it to mercury to see if they will warranty it. I think they will, there was no impact to it. I think it was a flaw in the casting that finally let go. just glad it didn't throw the ear while I was running.
I am trying to find a set of 15 x 28 to get a little more rpm's out of the motors when I am loaded with fuel and people. The 15x30's work great with three people and less than 3/4 tanks. turning around 6500. but with a full load like the dam run, I could only get 6000 out of them. I think this would be a good size to have as a backup set. anyone think of a better size to try?????

[mbrown2]

Hey all,
Been out of town for a while. thanks for the info here.
The reason for the prop search is I cracked one of the labbed 4 blade 15X30's I had on the boat. Sent it to mercury to see if they will warranty it. I think they will, there was no impact to it. I think it was a flaw in the casting that finally let go. just glad it didn't throw the ear while I was running.
I am trying to find a set of 15 x 28 to get a little more rpm's out of the motors when I am loaded with fuel and people. The 15x30's work great with three people and less than 3/4 tanks. turning around 6500. but with a full load like the dam run, I could only get 6000 out of them. I think this would be a good size to have as a backup set. anyone think of a better size to try?????
GG, if you would like to try a set of 4 blade 15x28 cleavers non labbed, I have a set you can try....In talking with Lew at Lakeland, he seems to like the Bravo 1 28 or 30" with holes....lots of guys running them with pretty good combination or all around performance.
I will probably get a pair after I get my hands on another 30x14.5 3 blade labbed to match the one that threw a blade...

[STV_Keith]

Try Kevin at R& R Prop Shop (http://www.randrpropshop.com) in Henderson, NV. I know he has a few sets of the big wheels on the wall used. :)
702-564-7502

[the_gray_goose]

GG, if you would like to try a set of 4 blade 15x28 cleavers non labbed, I have a set you can try....In talking with Lew at Lakeland, he seems to like the Bravo 1 28 or 30" with holes....lots of guys running them with pretty good combination or all around performance.
I will probably get a pair after I get my hands on another 30x14.5 3 blade labbed to match the one that threw a blade...
Thanks mike
I may take you up on that offer before I buy a set.
I herd about the bravo 1"s also, does lou have any there as lowners?

[mbrown2]

Thanks mike
I may take you up on that offer before I buy a set.
I herd about the bravo 1"s also, does lou have any there as lowners?
I was in LL a couple weeks ago, and did not see anything on the wall that was big and matching