Have to vent....................................

[460 jus getn it]

So im having a couple parts painted. Im having the tiller arm and the arm that hold the diverter cable painted. WHO uses red lock tight :mad: :mad: :mad: , i now have two screws that are destroyed and i still havent got them out. WHO ever took this apart used red focking lock tight to hold the screws in. Hello, last time i checked anti-seeze is the way to go. So now i have to get the remaining parts of the screws out with out destroying the threads........WOO HOO............................................... ..

[Devilman]

So im having a couple parts painted. Im having the tiller arm and the arm that hold the diverter cable painted. WHO uses red lock tight :mad: :mad: :mad: , i now have two screws that are destroyed and i still havent got them out. WHO ever took this apart used red focking lock tight to hold the screws in. Hello, last time i checked anti-seeze is the way to go. So now i have to get the remaining parts of the screws out with out destroying the threads........WOO HOO............................................... ..
Oh yeah. Nothing like going back & fixing someone else's half-ass repair work. Hope it don't give ya too much trouble. :cool:

[maxwedge]

Loctite makes a solvent that dissoves that stuff, or at least they used to. Of course I don't remember what it's called though. But if you are in a hurry, power tools, fire, and large hammers are the way to go. :)

[Squirtcha?]

Loctite makes a solvent that dissoves that stuff
Sometimes a little heat from a propane torch will work too.
As I'm sure you know, that's gonna be real tough drilling those screws for and ezout or just plain drilling em out. Stainless is way harder than aluminum and that drill's gonna wanna walk over to the aluminum for sure (unless you're dead center with the drill when you start).

[jrork]

Gonna agree with Squirt here. A little bit of heat from a propane torch works wonders. Found that out once when somebody before me when Loctite crazy. Couldnt get anything loose and then out of hate poured some heat to it. Was like butter after that. Go figure. Good luck

[396_WAYS_TO_SPIT]

460 was too lazy to get the torch out:D he likes to take the "hard road" in life :D

[EMCAM]

This loctight crap isnt going to be the reason you dont make it to the lake to run me is it?????????????????????

[EMCAM]

cuz i got somthing 4 you .

[396_WAYS_TO_SPIT]

cuz i got somthing 4 you .
Sure ya do........ Look below your name!!!!!!!!!!!!!!!
That says it all!!!!!!!!!!!!!!!
WIDE F*CKING OPEN form the front to the back! Choppy water and alll :220v: :220v: :220v: :220v:

[EMCAM]

Dont hate me cuz i aint skeerd

[Jordy]

460 was too lazy to get the torch out:D
I heard he had his torch out but was using it to heat up his crack pipe. :D :D :D

[Glencoe MiniDay]

They Probably used it at the factory where the pump was made.
I bought a new American turbine pump for my boat and had to take it all apart to have it powdercoated because it only came in white.

[Big Kahunaa]

red locktight will come apart a 350 deg's get the fire out

[396_WAYS_TO_SPIT]

red locktight will come apart a 350 deg's get the fire out
He knew that...... :rolleyes: :rolleyes: He just wasnt using his brain:D
I luv your pic!!!!!! You need to bring her to mesa;)

[Glencoe MiniDay]

Looks like you have been very busy 396.
Looks very nice though
Thanks for all the information on the pump install.
Gotta get out of here this morning to go make some money to keep the ball rolling if you know what I mean.
Off to work for the 40 dollar an hour side job.

[Big Kahunaa]

I luv your pic!!!!!! You need to bring her to mesa;)
when i find her i'll be sure to wing her by

[Devilman]

If you haven't gotten it fixed by now, just put some spinner hubcaps on your boat trailer. That will take your mind off the whole deal.... :rollside:

[cave]

Ty, did you rebuild the pump?