parts swapmeet thread?

[dave186]

isnt it about time for another one? im ready to start gathering stuff to tinker with this winter!

[TRG]

i did not have the time to take pis tonight but im on it tomorrow for a grip of shit to get rid of!

[dave186]

good deal, not that i really need a grip of shit. i might try to convince myself that i need to get rid of some junk i am holding on too.

[396_WAYS_TO_SPIT]

good idea;) I'll start another thread;)
396

[Squirtin Thunder]

good idea;) I'll start another thread;)
396
That was a great idea Dave !!!http://www2.***boat.com/image_center/data/520/2311logo_fordracing-thumb.gifhttp://www2.***boat.com/image_center/data/520/23112734avatar8845_2-thumb.gifhttp://www2.***boat.com/image_center/data/520/2311logo_fordracing-thumb.gif

[P-Money]

Rewarder TT headers for a BBC. Nice shape, although chrome is blued. Water lines included. $350 plus shipping.
Measurements:
Longer of the Two:
36" overall, 17" from the rear header bolt to the end, 3 3/4" from the water fitting to the end.
Shorter of the Two:
32 1/2" overall, 14 1/2" from the rear header bolt to the end, 1 1/2" from the water fitting to the end.
http://www2.***boat.com/image_center/data/500/540DSC00819.JPG
http://www2.***boat.com/image_center/data/500/540DSC00815.JPG
http://www2.***boat.com/image_center/data/500/540DSC00817.JPG

[Jim Hall]

I am looking for a set of TT headers for a 460 Ford and SVO,Ford motor sports valve covers (tall).

[BAE_557]

RCD 1750 14MM GT blower belt, 8 total runs.
IMCO Marine polished puke tank with -12 AN Earl's braided steel lines and fittings.
A total of (6) motor plate to frame rail blocks, they have 4* machined into them.

[GUGS102]

P-Money,
I'm interested in the headers, I sent you a PM.
Thanks,
Gugs

[FASTRAT]

RCD 1750 14MM GT blower belt, 8 total runs.
IMCO Marine polished puke tank with -12 AN Earl's braided steel lines and fittings.
A total of (6) motor plate to frame rail blocks, they have 4* machined into them.
lets see some pics!
fastrat

[CMZRACING]

Anybody Have A Set Of Zoomies For A Bbc? Would Like To Get A Set For The Every Now And Then Times.

[slotracer]

got a set of zoomies with the water lines. $250.00 b/o in decent shape not new but not junk.
http://www2.***boat.com/image_center/data/520/393zoomies_1-med.jpg
http://www2.***boat.com/image_center/data/520/393zoomies_2-med.jpg
http://www2.***boat.com/image_center/data/520/393zoomies_5-MED.jpg
pat(slotracer) :coffeycup

[GUGS102]

http://www2.***boat.com/image_center/data/520/2928PA250510-thumb.JPG http://www2.***boat.com/image_center/data/520/2928PA250507-thumb.JPG
I have a set of 1.88/2.19 w/ 3/8 stem, standard length stainless valves with only 20 minutes on them. I also have comp springs #911-16 with the matching 20 minutes. Switched to a roller set up which required new springs and +.100 longer stems.
Valves - $125+ shipping
Springs - $75 + shipping
I'm just trying to get some of my money back. I know there are many motors to be built over the winter, these are good parts, save some money and get them out of my shop!!
The rotators and retainers are not new but still good.
Thanks

[FASTRAT]

Hey Tony...
Quit goofing off lol :) & get my pics for me
Ron

[Taylorman]

Teleflex marine tachometer, white.
Teleflex white volt gauge
MSD window switch with relay
BBC 3 point motor mounts and driveline
BBC Bassett twisty headers
Dooley dual air scoop, 9" center to center spacing. Fits Oldsmobile tunnel ram or other 9" spacing.

[mares98]

new dart tunnel ram 9.8 deck for a b.b.c. polished 675.00.misc msd rev control & retard, Used Holley mech fuel pump, used holley electrical fuel pump 280 gph. Used polished pair of 481 rodeck tall valve covers 250.00 Feel free to make an offer on any of these parts. 909-463-6264

[ARS Marine inc.east]

Lookin GOOD

[RCB19]

I have a Clay Smith Cam for a BBF 429/460. It's a solid flat tappet grind # C-292-8-B. Specs are 292* adv duration and 240* @ .050 int/exh with a 570 lift int/exh, 108* lobe center. The cam only has about 2 hrs total run time on it. Bottom end went in the motor that it was in and we decided to go a different route on the next one. Had the cam checked by Clay Smith and it is in perfect condition.

[GUGS102]

I have two carbs in great shape. PM if interested
First is a 750 edelbrock, marine carb PN# 1410, electric choke - $175
http://www2.***boat.com/image_center/data/500/2928PB090547.JPG
Second is a holley 3310 750, vac secondaries, manual choke $125
http://www2.***boat.com/image_center/data/500/2928PB090549.JPG

[Tahiti350]

Mix and Match sale:
'76 Witchcraft 16' hull w/WJ pump. Hull is clean and solid, bottom looks like new, have mounts and stuff for 455 Olds. no steering, wiring, seats are good for pattern use. Clear Washington title. $500
http://www2.***boat.com/image_center/data/500/2266Witchcraft_1.JPG
'88 Pontiac Safari wagon, stout 400 Pontiac, th400, lots of good stuff, (air lift bags, receiver hitch, Toyo 800 235/75/15 on Buick alloy's, 70+% tread), complete 2 1/2" dual exhaust w/Raptor mufflers (could be reworked slightly and put on a Chevy pickup or possibily Chevelle chassis).The 400 Pontiac is already "hotrodded" and was planned for the Witchcraft above. We used it to tow the Tahiti over 600 miles for Labor day this year, ran excellent, lots of power, Clear Washington title. $1000
http://www2.***boat.com/image_center/data/520/2266MVC-019F-med.JPG
http://www2.***boat.com/image_center/data/520/2266MVC-018F.JPG
Single axle trailer for Flat bottom V-drive, approx 18', very solid, not very pretty, Clear Washington title, will replace wheels and tires for safe delivery. $400
http://www2.***boat.com/image_center/data/500/2266trailer2.JPG
I could make it a package deal; loaded, hooked up, and ready to drive home for $1600 cash.
80's Kawasaki KZ80, runs, but difficult to start. have signed title $250

[supersoaker509]

RCD 1750 14MM GT blower belt, 8 total runs.
IMCO Marine polished puke tank with -12 AN Earl's braided steel lines and fittings.
A total of (6) motor plate to frame rail blocks, they have 4* machined into them.
Just sent you a PM

[BAE_557]

Just sent you a PM
The tank and lines are shown below, the stainless mounting straps are also included.
The other side of the tank has the same exact line as shown in the picture.
http://www.hotboatpics.com/pics/data/3021/1870MVC-017F.JPG

[PC Rat]

American turbine suction housing with hardened shaft $200. Has had a spun wear ring.
I took the suction to American Turbine, they said that they can fix the wear ring surface for $150. He said the shaft is slightly undersized as well and can be fixed for $50.
He said that the suction is $765 new and the hardened shaft is $500 new - Somebody can have this and get it fixed for total of $400
http://www.jetheaven.us/photopost/data/500/98AT_Suction-med.JPG
Aggressor impeller - a couple small cracks and can be welded $90
http://www.jetheaven.us/photopost/data/500/98Agg_Impeller_1-med.JPG
Pair of Hardin Exhaust Manifolds for BBC $600
http://www.jetheaven.us/photopost/data/500/98Hardin_Manifold-med.JPG
Spreadbore / Squarebore carburetor adapter $12
Mallory coil $18
http://www.jetheaven.us/photopost/data/500/98Spacer_Coil.JPG
Pair of sideways mount carb adapters - new and unopened $30
http://www.jetheaven.us/photopost/data/500/98Carb_adapter-med.JPG
Pertronix ignitor points conversion $40
ARP stainless valve cover studs 14pc set (new in package) $20
Speed-Pro plasma moly ring set for .030 over 454 - #R-9590035 file to fit (new in box) $80
Mallory Comp 9000 distributer with bronze gear for Chevy $120 also have the Mallory coil for this distributer $25
Ultradyne roller cam 255/264 duration .685/.670 lift for BBC $120
Oil pan for BBC in early Nova, with oil pump $150
http://www.jetheaven.us/photopost/data/500/98Nova_Oil_Pan-med.JPG
Everything obo, + shipping
Boat in signature for sale also.
Brian

[bigkatboat]

I have a 455 Olds for that boat! All in parts, new bearings, everything, exhaust, intake HEI, oil pan, starter, everything except; cam, carb, and a gasket set. $375.00

[wasted$$]

I have a 455 Olds for that boat! All in parts, new bearings, everything, exhaust, intake HEI, oil pan, starter, everything except; cam, carb, and a gasket set. $375.00
check your pm.

[79Brendella?]

Mix and Match sale:
'76 Witchcraft 16' hull w/WJ pump. Hull is clean and solid, bottom looks like new, have mounts and stuff for 455 Olds. no steering, wiring, seats are good for pattern use. Clear Washington title. $500
http://www2.***boat.com/image_center/data/500/2266Witchcraft_1.JPG
'88 Pontiac Safari wagon, stout 400 Pontiac, th400, lots of good stuff, (air lift bags, receiver hitch, Toyo 800 235/75/15 on Buick alloy's, 70+% tread), complete 2 1/2" dual exhaust w/Raptor mufflers (could be reworked slightly and put on a Chevy pickup or possibily Chevelle chassis).The 400 Pontiac is already "hotrodded" and was planned for the Witchcraft above. We used it to tow the Tahiti over 600 miles for Labor day this year, ran excellent, lots of power, Clear Washington title. $1000
http://www2.***boat.com/image_center/data/520/2266MVC-019F-med.JPG
http://www2.***boat.com/image_center/data/520/2266MVC-018F.JPG
Single axle trailer for Flat bottom V-drive, approx 18', very solid, not very pretty, Clear Washington title, will replace wheels and tires for safe delivery. $400
http://www2.***boat.com/image_center/data/500/2266trailer2.JPG
I could make it a package deal; loaded, hooked up, and ready to drive home for $1600 cash.
80's Kawasaki KZ80, runs, but difficult to start. have signed title $250
I like the WitchCraft. Does the $500 include delivery to Vegas? C'mon I know you want to come to Vegas. lol

[Tahiti350]

I suppose I could get it there in two trips, won't fit in the back of the truck in one piece...
Seriously, $500 will get it as far as Southern Oregon, just a short jump from Vegas. For an extra $400 I'll put bunks on the trailer and you could just hook up and go from there.... :D
I would like to take the wife to Vegas, but just spent $2000 on the truck this month, so no Vegas trip for us. :cry:

[bigkatboat]

Olds motor gone.....THANK YOU!