Everything must go...SPAM ALERT!..Lots of Pictures [Archive]

Cole Sanger

09-01-2003, 10:36 PM

Well, here I go again. Thought the old engine was going to be a no brainer. Guess again. So, I have to sell some stuff (EVERYTHING MUST GO), to get a new engine. Here is a list.
1.1972 Sanger Flatbottom Hull. New white gel inside and out. SOLD
2.Casale 12 degree v-drive. When the purchaser gets it, it will have a new top shaft, bearings and seals. Waiting on top shaft and seals as you read.
3.Hall-Craft parralel shaft v-drive. Needs seals and bearings.
4.Powerglide transmission. Converted to manual shift only and has direct drive converter.
5.Parts from the old engine. Just getting into the engine now, so not sure what is good. Possibly the closed chamber small valve heads, the intake (SOLD) is polished and in good shape, M/T 427 valve covers(SOLD) (also polished), e-mail for more on the engine.
6.Seats. Brand New. Four fiberglass seats with white covers (purple pipeing). Not race seats by any means. They are originally for a baja vehicle, but could be used in a boat.
7.Bassett BB Zoomies. Brand New. Never been used once. They are chrome with baffles installed by Bergeron Eng.
More to come. I have pictures. Let me know what you want to see. I can post, and will start posting tomorrow. I need some help on this. I just bought Semi-V's boat. Pick it up Sunday. I need to get some money to get another engine. Not sure if anyone is interested, but could possibly do some trading. Two boats without one engine between them. Thanks, tell your friends.
Cole_Keefer@cox.net
[ October 03, 2003, 04:59 PM: Message edited by: Cole Sanger ]

dmontzsta

09-01-2003, 10:45 PM

how much for the V-Drive? splitcase?

Cole Sanger

09-02-2003, 07:37 AM

I would like to see 1000 for the 12 degree. Completely rebuilt with a new plate. The zoomies are 500 and the transmission 200. The hull I need 2000. The seats I would like to see 200 and the Hall-craft I would like 200. All prices are negotiable, to a point.

1980SANGERV-DRIVE

09-02-2003, 04:42 PM

Cole Sanger

09-02-2003, 09:14 PM

A friend of mine has a motor for a boat with headers and wants a v-drive . What can be worked out to give him the boat to drop his motor in it ?
He has a jet with a cracked hull, and I want to get him out of it.
Now there is a question. If he is looking for a project, at a good price, you have come to the right place. I have almost everything you would need. The hull, v-drive, powerglide if you want, or the drive-shaft that was in the boat, aluminum to box in the stringers from front to back(already cut, just need to be installed), all the steering stuff, new gaffig gauges and bezels, foot throttle, four seats if you want. What you would need is tanks, although I was going to buy some from david 396. I don't know if he still has them. You would need to buy a prop shaft. I think that is a pretty good list of what I have. There is probably more that I am forgetting. All that for 3200 obo. The only thing I am waiting on is the top shaft for the casale. You said he already has headers, so that price doesn't include the zoomies. I think that is a fair price, but you tell me what you think. I will post some pictures in a few minutes.

Cole Sanger

09-02-2003, 09:51 PM

Some pictures. I am waiting on my camera battery to charge.
Hull. HULL and TRAILER are SOLD
http://www.***boat.com/image_center/data/506/643119-1953_IMG.JPG
Seats.
http://www.***boat.com/image_center/data/506/643Fiberglass_seats.jpg
Hall-Craft.
http://www.***boat.com/image_center/data/500/643Hallcraft_and_Motor_plates.JPG
I thought that I had some pictures of the casale before it was taken apart. I guess not. I will take some of the tranny and the zoomies tomorrow and post them.
[ October 03, 2003, 05:00 PM: Message edited by: Cole Sanger ]

stilettovdrive

09-03-2003, 06:22 AM

How much for the seats??, Gotta love them.
You will have to ship them to DK, but i pay in advance if you like!!
The viking.
By the way.
3200 is more then fair.

T-Bag

09-03-2003, 10:20 AM

1980SANGERV-DRIVE:
A friend of mine has a motor for a boat with headers and wants a v-drive . What can be worked out to give him the boat to drop his motor in it ?
He has a jet with a cracked hull, and I want to get him out of it. I've got a 1977 hondo t-deck runner that is already to go minus engine (set up for BBC) in excellent condition looking to get $6400 out of it. everything either polished or anodized. went tthrough the whole boat last winter.

Cole Sanger

09-03-2003, 10:25 AM

It's 200 for the seats. Give me a zip code and I will go get a price for the shipping.

Lookin for Liquid

09-03-2003, 10:28 AM

Did not know Denmark had zip codes?

Cole Sanger

09-03-2003, 10:33 AM

Guess I should have said shipping info instead. Didn't look at where he was before I typed.

1980SANGERV-DRIVE

09-03-2003, 04:29 PM

It is 5:25 now Ill talk to Dave tonight when he gets off work and get back to you. He was interested last night. Do you have more seats if you sell these? Thanks for the speedy return message. Rich :cool:

mickeyfinn

09-03-2003, 05:26 PM

Do the seats have brackets on them to be stringer mounted?

stilettovdrive

09-03-2003, 07:30 PM

I just checked out KIT and Buggy service, and for a 100 dollars more i can get seats in the right colour and all, so i'm out of the deal.
And yes, we have ZIP or postal codes here, we are only 6 million people here, but it can be hard to get around without some sort of system.
We have flushing toilets, hookers from estonia ,asphalt on the roads, and bitches with piercings in the most odd places too.
The viking.

Cole Sanger

09-03-2003, 07:41 PM

I bought them from Pape Enterprises in El Cajon, CA. You can check the web site. I paid, with shipping, over 450 for them. Sorry they aren't the color you need. No, they don't come with the mounting hardware. That's the easy part though. You just need some angle aluminum and drill some holes. Very easy to mount them. I don't have other seats for the boat. Like I said though, I would rather sell everything in one transaction. I need the money and the room for that matter. Rich, just let me know when you can. Not a big rush. Although, the sooner I get some money, the sooner GoFastRacer can get another project. :D
[ October 03, 2003, 05:01 PM: Message edited by: Cole Sanger ]

Hud

09-03-2003, 07:48 PM

Bagpipes, how about some pictures of the latest paint job on that boat for sale, & some of Mikes new paint on the Howard! :D

stilettovdrive

09-03-2003, 08:36 PM

Oh no, colesanger, don't get me wrong, i do not doubt the price,teh price is fair. but with a 100 bucks worth of shipping, and possibly some new covers and importtax of 27,5 % ( not that big a deal, my aunt makes these things), its probably easier to just get them in DK.
I'm sorry i reacted without thinking, i'll do better next time.
If i had been finished with my current boat, i probably would have bought the whole thing for import myself, as i think the price is more then fair on the package deal, wich probably could be negotiated down to 3000 bucks.
A thing like that would cost around 6000 dollars here, if you could ever find one,.
The viking.

Cole Sanger

09-03-2003, 09:11 PM

I have no hard feelings. I just wanted you to know where to get the ones I am selling. If someone wanted different colors or something, I have no problem showing them where they are. Like I said, I am selling them for half the price. Just need the money. Itching to get the new boat going. It's been a long time since I have been on the water, much less in my own boat. Good luck on your project.

Cole Sanger

09-03-2003, 09:19 PM

Just saw another post for someone elses boat. I thought that I could make the same offer to deliver free to Red Rock if that would help anyone. I don't live that far away. I am not planning on going, but if someone really wanted it, I could take a day and deliver.

stilettovdrive

09-03-2003, 10:33 PM

Well, cole sanger. It's been 10 years since i have run anything faster then my dads fishingboat.
( Quicksilver with honda 15, What a rush)
My old boat got stolen and vandalized, and then kids, house, paintingcompany and so on, so i know the itch.
My problem is'nt money, but time, and the fact that i'm building a boat that i can't get parts for in DK wich slows things down a lot.
Most things is there thoug, and i,m aiming for the spring.
If needed i will take 2 weeks of and work fulltime in the winter, where the paintingbuisyness is'nt so busy.
The damn thing is going in the water, thats for sure.
I could take it for a spin in a matter of days, but it has to be totally finished before i start using it, complete with Graphics,vikinghorn, and all.
The viking.

Reds75Makai

09-04-2003, 12:22 PM

Cole Sanger, this is Rich's (1980Sangerv-drive) friend Dave. I am really interested. That would be a perfect project for me for the winter!!

Cole Sanger

09-04-2003, 06:31 PM

Sounds good. I will e-mail you in a little while. I have to go get some KFC.

1980SANGERV-DRIVE

09-07-2003, 04:40 PM

What another project, what are we thinking of?????
This is 3 now. You have more than I do now. jawdrop

Reds75Makai

09-08-2003, 05:44 AM

Yah but one of the projects I'm selling...so that will only be two projects...which will be keeping me busy for a while.

Cole Sanger

09-09-2003, 08:08 AM

Sorry to everyone that has been asking for pictures. Here's a picture of the valve covers and the intake manifold. The intake manifold is oval port. I have the pictures of the zoomies on the camera. I will upload them later today when I get home from work. MANIFOLD and VALVE COVERS are SOLD
http://www.***boat.com/image_center/data/500/643Valve_Covers.JPG
http://www.***boat.com/image_center/data/500/643Intake_Manifold.JPG
[ October 03, 2003, 05:03 PM: Message edited by: Cole Sanger ]

Cole Sanger

09-09-2003, 10:05 PM

And now, finally, the Zoomies with baffles. As you can see, they have never been on a running engine. I bolted them to my engine just to keep them safe. Other than that, they are brand new.
http://www.***boat.com/image_center/data/500/643Zoomies.jpg

Cole Sanger

09-30-2003, 09:37 PM

Ok, here it is again. The boat is now sold, along with the intake and valve covers. So, look to the top of this thread to see if anyone is in need. I still don't have the top shaft for the Casale. I will let it go for 650 as is with the new plate that GoFastRacer cut for me. I have some bronze underwater hardware if anyone needs. I also have some Gaffrig II white face gauges and purple angle bezels if anyone wants. They are brand new, still in the boxes. I also have a Weiand high rise manifold that needs to be polished again, it has a single carb adapter plate on it.

Reds75Makai

10-01-2003, 08:30 PM

Cole,
just wanted to let you know that I made it back in one piece. :cool: thanks again!!

Cole Sanger

10-01-2003, 09:56 PM

Glad to hear you made it. You know you forgot the trailer lights. What do you want me to do with them? I found them about an hour after you left.

Cole Sanger

10-03-2003, 10:47 AM

More stuff for sale.
http://www.***boat.com/image_center/data/506/643122-2208_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2207_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2209_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2210_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2211_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2212_IMG-med.JPG http://www.***boat.com/image_center/data/506/643122-2213_IMG.JPG

Cole Sanger

10-03-2003, 10:50 AM

And Then, No And Then!
http://www.***boat.com/image_center/data/506/643122-2214_IMG.JPG
http://www.***boat.com/image_center/data/506/643122-2215_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2216_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2217_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2219_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2220_IMG-med.JPG

Cole Sanger

10-03-2003, 10:54 AM

And Then, No And Then!!
http://www.***boat.com/image_center/data/506/643122-2221_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2222_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2223_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2224_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2225_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2226_IMG-med.JPG

Cole Sanger

10-03-2003, 10:59 AM

I said No And Then!!!
http://www.***boat.com/image_center/data/506/643122-2227_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2228_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2229_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2230_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2231_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2232_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2233_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2234_IMG-med.JPG

Cole Sanger

10-03-2003, 11:03 AM

And Then!!!!
http://www.***boat.com/image_center/data/506/643122-2235_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2238_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2239_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2240_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2241_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2242_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2243_IMG-med.JPG
http://www.***boat.com/image_center/data/506/643122-2244_IMG-med.JPG

Cole Sanger

10-03-2003, 11:11 AM

Ok, I think that is enough pictures for one day. Good thing I have a cable modem. That would have taken a week on dial up. Anyway, I know this isn't the best stuff anyone has seen. The gauges and bezels are brand new though. The steering shaft is new and the rudder stuffing box is new (did have to sand down the bottom of it to get it to sit flat while mocking up, never installed it though). The heads are oval port closed chamber from my 427. The crank is in good shape also, it too is from the 427. Haven't had anything checked out professionally. The carpet is marine grade purple, never had a chance to install it. It all has to go. Let me know what you think. The Weiand high rise had a blemish on it that I had welded. It will need to be cleaned up. It is set up for a single carb, but I am sure you can get a dual carb top plate for it if needed. The casale is complete minus the top shaft, the pictures don't show all the other parts in the box.
[ October 03, 2003, 12:16 PM: Message edited by: Cole Sanger ]

dmontzsta

10-03-2003, 11:24 AM

Wow, that is alot of work.
I hate to ask, but would you mind posting prices?

Cole Sanger

10-03-2003, 11:39 AM

I really don't know right now what I want for most of it. I posted some prices up above. This is just what I have. I just want to get rid of it all. I really don't have the room for it, or the need for it all. Hopefully if someone needs any of it they will just let me know and we can go from there. I will try to think about what I want for it. I am thinking 2000 for everything. That includes the zoomies, casale, hallcraft, seats, gauges, high rise intake, carpet and all the other stuff. I doubt that anyone will want it all in one swoop, that would be too easy for me.

dmontzsta

10-03-2003, 12:52 PM

you have PM
[ October 03, 2003, 02:03 PM: Message edited by: dmontzsta ]

Cole Sanger

10-03-2003, 01:41 PM

I hope everyone knows that the boat, trailer, edelbrock manifold and valve covers have been sold. I posted that last week, but I didn't really think about someone not reading all the posts so far. Hope that doesn't confuse anyone. eek!

Heatseeker

10-03-2003, 07:58 PM

What diameter is the foam grip steering wheel? What kind of shape is the chrome(can't really tell by the pics)in and how much?
Thanks!

Cole Sanger

10-03-2003, 08:32 PM

I think it is 10 inches. It's not in that great of shape. You could probably clean it up, but I only want $10 for it.

mickeyfinn

10-04-2003, 08:54 PM

How much for the flywheel and the gauges? May be interested in the tunnel ram also. Did I see an oil pan in one of the pics?

Cole Sanger

10-05-2003, 08:17 AM

I need 100 for the high rise, and 100 for the gauges and bezels plus shipping.Sorry, the flywheel is already sold. I am keeping the oil pan for the new engine.

AZKC

10-05-2003, 08:26 AM

Whats the H-block fit and whats the story on the heads?
KC

FlatStupid

10-05-2003, 10:08 AM

How much for the tennis shoe? :confused: :D

DansBlown73Nordic

10-05-2003, 10:10 AM

Its FREE!!! wink

Cole Sanger

10-05-2003, 10:16 AM

The "H-Block"? Is that what you call this?
http://www.***boat.com/image_center/data/506/643122-2226_IMG-med.JPG
The Nicson part in in the lower left?
It holds the driveshaft cover in between the v-drive and the engine. Here is what it looked like in the boat, a long time ago. (middle picture)
http://www.***boat.com/image_center/data/500/643Boat_before2-med.JPG
The heads are oval port closed chamber. They look good, but I have not had them in to a shop yet to have them looked at. They were on the engine and worked great when it was running. I don't know what else I could tell you about them other than that.

Cole Sanger

10-05-2003, 10:18 AM

I was wondering when someone would ask about that. ONE MILLION DOLLARS!!! With all that stuff in the garage, I can hardly walk, much less try to take pictures.

DansBlown73Nordic

10-05-2003, 10:30 AM

You have a e-mail.. wink

Cole Sanger

10-05-2003, 11:14 AM

Looks like the flywheel is still forsale if anyone is interested.

mickeyfinn

10-05-2003, 11:18 AM

Give me a package price for the flywheel, tunnelram and the gauges/bezels. Also if you could give me an idea of weight I could see how much freight is gonna set me back.

Cole Sanger

10-05-2003, 12:25 PM

Looks like Dans66Stevens beat you to the gauges and bezels.If he decides he doesn't want them, I will let you know. He said he was going to look at the parts I have and make a list. As far as the manifold and flywheel, I need 150 total. 100 for the manifold and 50 for the flywheel plus shipping.

P-Money

10-05-2003, 12:41 PM

Are those 1.22 gears? If so, would you be willing to let them go?

Cole Sanger

10-05-2003, 01:26 PM

They are 1.22 gears, but at this point I would really like to keep the casale as a whole package minus the top shaft. I will keep you in mind though if no one else wants the box. I am asking 500 for the casale as is. It would take a top shaft (175 Menkins) and a gasket set (25 Menkins) to put it all back together.

mickeyfinn

10-05-2003, 04:06 PM

Looks like the parts in the pictures I see two flywheels. Which one are you getting rid of? I am looking for one like the one on the left. It looks like the one on my 402 which has spun the ring gear on it.

GofastRacer

10-05-2003, 06:55 PM

Both the flywheel and flexplate are internally balanced so either will work on a 402!.. :)

Cole Sanger

10-05-2003, 08:58 PM

I actually have one flywheel and two flexplates. One of the flexplates is brand new. Anyway, today is buy one get one free day (on flexplates that is). 40 for both or 20 each. One has some surface rust from sitting in my garage.
http://www.***boat.com/image_center/data/520/643122-2245_IMG-med.JPG

Cole Sanger

10-05-2003, 09:00 PM

Hey, lookie there. I am rated now. Thanks to whoever threw me some stars.

AZKC

10-06-2003, 02:07 PM

Nope not that, this H-block
http://www.***boat.com/image_center/data/506/643122-2212_IMG-med.JPG
And can I get the casting numbers off the heads please.
KC

mickeyfinn

10-06-2003, 02:53 PM

Any idea how much freight will be to zip code 30519? For the Tunnel Ram and the flexplates. Just need one of the flexplates. Probably cost as much to ship one as they cost.
Prefer the new one.... :D

396_Z

10-06-2003, 04:06 PM

Do you still have the steering shaft (with componets) and the new rudder stuffing box?
I'd be interested in taking those off your hands of the pricing is right.
Mike

Cole Sanger

10-06-2003, 04:43 PM

I had a 50/50 chance on the H-Block. I guessed wrong. The H-block was 80 bucks from Mesa Driveline. The whole assembly I will sell for 60, or just the h-block for 40.

Cole Sanger

10-06-2003, 05:18 PM

The steering shaft is brand new. I have all the components. Dan66Stevens has asked me about the steering post that bolts to the dash. I think he wants it, but I am not positive. I told him 10 bucks for the post. I have a complete cable steering assembly. If he doesn't want the steering post, I can let the whole thing go for 200. That doesn't include the rudder. That includes the post, new shaft, bearings, pullies (3 pieces), chain, chain gear, stuffing box, steering quadrant. The stuffing box is new except we sanded the bottom so it would sit flat on the hull, but it was never installed. I will sell it for 30.

Cole Sanger

10-06-2003, 05:22 PM

The shipping (manifold/flexplate) I would have to box it up and take it to the post office to get you a price. I have to take a couple of parts there anyway. I will try to get you a shipping price in the next couple days if that is ok. I would think that shipping wouldn't be that much more for the flexplate. I think you can get new ones for less than 50 at any checker/shucks/kragen. It is up to you though. Let me know what you decide.

slotracer

10-06-2003, 06:14 PM

pm me with a price on the zoomies.
thanks pat(slotracer) :D

Cole Sanger

10-06-2003, 09:37 PM

The zoomies I am asking 500. They have never been run. I bought them, had Bergeron install baffles, then never have had the chance to run them. They cost me over 650 before tax and shipping. You will save yourself money buying mine, if you were to buy them brand new from Bassett. The 500 is only going to help someone that was going to buy brand new from them.

Cole Sanger

10-07-2003, 02:02 PM

AZKC, Sorry about that. Just re-read your post. You asked about the heads casting number. They are 3931063. Trying to keep up with all the people and all the questions and the places to ship. It's like a second job. Better than not being able to sell it though. Hope it all goes to people that need it.

mickeyfinn

10-07-2003, 03:26 PM

Just to save someone some time looking up the numbers here is what I found:
3931063....68-69...oval..CLOSED..396, 402, 427

1980SANGERV-DRIVE

10-07-2003, 04:01 PM

how much for the tunnel http://www.***boat.com/image_center/data/506/643122-2239_IMG-med.JPG ram???

Sangster

10-07-2003, 04:10 PM

Are you buying it .. or selling it

BigBoyToys

10-07-2003, 04:26 PM

1980SANGERV-DRIVE:
how much for the tunnel http://www.***boat.com/image_center/data/506/643122-2239_IMG-med.JPG ram??? I have one of those for sale too......

Jetboatguru

10-07-2003, 04:29 PM

Am I the only one that finds Mickey Finn's avatar Fing hilarious ? :D :D :D

mickeyfinn

10-07-2003, 06:09 PM

Jetboatguru:
Am I the only one that finds Mickey Finn's avatar Fing hilarious ? :D :D :D I don't remember where I found it but I thought it was funny as hell. You are the first here to comment on it since I changed it.

DansBlown73Nordic

10-07-2003, 06:13 PM

I also thought it was pretty funny... :D

GofastRacer

10-07-2003, 08:19 PM

It's totally funny!!.. :D :D

Cole Sanger

10-07-2003, 09:40 PM

1980SANGERV-DRIVE, I do believe that MickeyFinn wants the tunnel ram and one flex plate. I am going to get the shipping info for him tomorrow. MickeyFinn, this is correct still right? If not, I will send you an e-mail. As far as the zoomies, no one has said they want them. Shoot me an e-mail (cole_keefer@cox.net) and we can set up shipping. I sent a pair of headers to northern CA and I think it was 50 bucks, so it shouldn't be more than that. Is this going on Daves new boat? Should have had him put them in the back of the truck for you. Would have saved on shipping. Anything else you see he might need? I was sure he would want the v-drive. He said he wanted to start with absolutely nothing. More power to him. I couldn't have done that. Cost way to much.

Fhat Cat

10-08-2003, 09:22 AM

Hey Cole,
see ya having a fire sale!! It going with the project? I jhave to say I miss the flattie! Hope you enjoy it as much as I did!
Send me some picks when you get it done. Also I am selling the oil pan that was in the boat. 14qt donlley cromed for v-drive BB chevy so if anyone askes if you have one send them my way. you know how clean it is...300 obo. Also just brought a b&m blower and bullard intercooler for the Cat engine.Should be in the way in about 2 months!!!
If anyone is intrested in the oil pan email mjm03@pacbell.net
AKA simi flatie

Cole Sanger

10-08-2003, 11:16 AM

I never thought about it that way, but that sure is what it seems like. Sounds like your project is comming along. I am waiting to sell all this stuff so I can build one myself for the flat. I will send you all the pictures when it gets done, but you already have pictures of what it is going to look like. That is what I am going to go by when I put the new engine in.

Cole Sanger

10-08-2003, 12:51 PM

MickeyFinn, I sent you an e-mail on the shipping for the tunnel ram and flexplate.
Dans66Stevens, I sent you the shipping info on the gaffrig gauges.
Dmontzsta, I sent you shipping info on the scoop.
1980SANGERV-DRIVE, I sent you the info for the motor plates. I will need your zip code so I can get you a shipping price on the zoomies. Let me know if you want the motor plates.
Not sure if anyone else had asked me for stuff. Send me an e-mail if you see anything you need.

brianwhiteboy

10-08-2003, 02:34 PM

Is the scoop still for sale? How much?

DansBlown73Nordic

10-08-2003, 04:11 PM

I got your info and will be sending a money order.

Cole Sanger

10-08-2003, 04:20 PM

brianwhiteboy, I don't think so. Dmontzsta is buying it. If he decides he doesn't want it, I will let you know. Thanks.

1980SANGERV-DRIVE

10-08-2003, 05:01 PM

How much for the ladder? http://www.***boat.com/image_center/data/506/643122-2244_IMG-med.JPG

mickeyfinn

10-08-2003, 05:16 PM

Cole Sanger
[QB] MickeyFinn, I sent you an e-mail on the shipping for the tunnel ram and flexplate.
I want the flex plate and the hi rise. I am guesing it will work with my oval port heads. How do you prefer payment? Money order, paypal? Just let me know and I'll send it to you. If the gauges don't sell let me know. I'm interested in them also.