Lab Finished Bravo Props

[40FlatDeck]

I have a set of Bravo 34's that came on my Spectre when I bought it last year. One had a slight ding so I sent them back and had them refinished. They have zero time since being refinished and have the XR hubs. I also have a Bravo 28 that was used once on my HTM. The 28 has a standard hub. I'll take 750 for the 34's and 300 for the 28. Thanks. This is like my third screen name if anyone noticed!:D F**king computers.
Erik

[andy01]

Hows your boat coming? Is it all back together?

[40FlatDeck]

Hows your boat coming? Is it all back together?
Almost. I sent alot of pieces off to get hard anodized and painted. Everything has made it back but we ended up doing a complete new fuel system and ran the water lines a little different along with bigger sea strainers. The big problem we ran into was when my lowers were getting the swept back skeg they found I had water in one of the units and it ended up eating a set of gears.:mad: Number 6 gears are a touch more than Bravo stuff.:D I should get the lowers back soon and we will be in business. The motors made big numbers so I am excited for this next year. I look forward to your 29 project.:)

[andy01]

Almost. I sent alot of pieces off to get hard anodized and painted. Everything has made it back but we ended up doing a complete new fuel system and ran the water lines a little different along with bigger sea strainers. The big problem we ran into was when my lowers were getting the swept back skeg they found I had water in one of the units and it ended up eating a set of gears.:mad: Number 6 gears are a touch more than Bravo stuff.:D I should get the lowers back soon and we will be in business. The motors made big numbers so I am excited for this next year. I look forward to your 29 project.:)
Right on, you know that is how it goes. When you start you find all the other little over looked stuff, and you get the "well while I am here I may as well change this". Good for you guys, I really look forward to seeing the finished project and going for a ride.
Ya the 29' should be a fun build I have a 588 inch quad rotor sitting at GT for it and 6 plug in gimble. Should be a neat Havasu boat for a little while, unless something changes and I end up in a 32' Skater. I dought it though, I haven't seen any lately that I felt were worth the money.

[707dog]

not to sound like a dumb azz but what is a lab finish? and what are the benifits to it??

[40FlatDeck]

not to sound like a dumb azz but what is a lab finish? and what are the benifits to it??
It's a process that helps you fine tune your prop for your application. Matching the props, thinning the blades, adding more cup, etc. On my HTM that 28 out of the box did 101mph. Had it finished and I gained rpm and did 104 in it. Just that little extra.:D

[40FlatDeck]

And............bump.:D

[40FlatDeck]

One more bump for some good props...........

[Havasu Carrera]

What side of the country are you on and how can I contact you about your props??? I tried to pm you but you have (no contact info?) Thanks Tim

[XFactor]

Will they fit Imco's?

[Todd969]

What side of the country are you on and how can I contact you about your props??? I tried to pm you but you have (no contact info?) Thanks Tim
He's in Tucson,AZ

[40FlatDeck]

What side of the country are you on and how can I contact you about your props??? I tried to pm you but you have (no contact info?) Thanks Tim
I'm in Tucson. I can ship them out for you or meet you in Phoenix. Give me a call 520-907-3904.
Erik

[40FlatDeck]

Will they fit Imco's?
Yep. Imco's use the same size as the XR shaft.

[Havasu Carrera]

Thanks for a great deal on a great prop! I can not wait to try it! Did you have 136 years in your HTM?? What kind of hp and rpm?? Do you remember by chance? Will see you at the cove for sure!! What kind of boat do you have now?? Thanks again Tim

[UnionJack]

Do you still have the 34's

[40FlatDeck]

Thanks for a great deal on a great prop! I can not wait to try it! Did you have 136 years in your HTM?? What kind of hp and rpm?? Do you remember by chance? Will see you at the cove for sure!! What kind of boat do you have now?? Thanks again Tim
Thanks Tim. :D My HTM made just a touch over 800 on the dyno and the drive was 1.36. The first time I ran the 28 straight from the box it did 101. After the blades were thinned and matched I ran it one more time and boat did 104 at 6200rpm. I have a 40 Skater right now. Just look for the Larrys Engine and Marine E-Z Up, right next to Predator. We will be there all week so stop by or give me a call and we will go for a spin.

[40FlatDeck]

Do you still have the 34's
Yep, they have not been run since the freshen up and come with Teague prop bags. The diffuser rings are cut off of these also. They are sweet.

[Havasu Carrera]

I would love to go for a (spin) in a 40! :jawdrop: Probibly makes my boat feel something like a row boat or possibly a Canoe. :sleeping: I will look you up for sure. See ya soon Tim

[UnionJack]

How would I pic them up?

[T-Bag'n]

Do you still have the 28???

[40FlatDeck]

How would I pic them up?
Give me a call, I can ship them to you.
520-907-3904
Erik

[40FlatDeck]

Do you still have the 28???
Sorry, I just sold it.

[40FlatDeck]

I still have the set of 34's if anyone is interested. I can ship them to you free of charge.

[Havasu Carrera]

I bought his 28 and got it in great shape today!! Good honest asset to the forums!! (I guess you guys already knew that)
Thanks Erik!! Can't wait to try it out! Who Labbed it by the way???

[40FlatDeck]

Thanks Tim. There is this old school guy in Tucson who has a prop shop. I tried a Mercury Lab finished after I tried this one he did and lost 2mph. He is the coolest guy with so much knowledge on how a prop should work, what to do to make it better, etc,etc. I can talk with him for hours. The best thing is there is only a one time charge until it is right. I have had him do at least 5 props and they always have worked perfect the first time. Thanks for the check! I have those strainers too if you want them. See you at Desert Storm.

[Havasu Carrera]

No prob on the ck was a good trade. LOL For sure Desert Storm. I am really strapped right now. I may be a boat bitch soon! sh.t. What would you let the sea strainers go for? I really only need one unless I get the super chiller some day. My boat had one prior but not now. Bro deal???LOL Thanks again either way!!!! :)

[40FlatDeck]

No prob on the ck was a good trade. LOL For sure Desert Storm. I am really strapped right now. I may be a boat bitch soon! sh.t. What would you let the sea strainers go for? I really only need one unless I get the super chiller some day. My boat had one prior but not now. Bro deal???LOL Thanks again either way!!!! :)
How does 100$ sound?:D