Neovane V-105

[napabob]

Looking for a big block Neovane pump with 1" diameter NPT inlet and outlet with center to center holes distance of 2 1/2".

[Jim Brock]

I pretty sure i have one call me tomorrow 818-890-1867,Jim

[napabob]

Jim,
I left a message and my cell phone contact number.

[napabob]

http://www.hotboatpics.com/pics/data/500/6782WaterPumpTopFront.jpg
http://www.hotboatpics.com/pics/data/500/6782WaterPumpTopRear.jpg
http://www.hotboatpics.com/pics/data/500/6782WaterPumpTopBottom.jpg
This is the top that I am trying to match up to a Nicson pump or Neovane V-105

[Jim Brock]

the top that is on the pump, looks better than that one and it's chrome, Jim

[napabob]

Jim,
I haven't cleaned and polished the top yet, I will post one when done.
Is the top brass/chromed or aluminum/chromed? Will you part with just the bottom half?
(707) 322-1260

[Jim Brock]

the top looks to be chrome brass, top goes with the bottom

[napabob]

Jim,
Does the top have a brand name and does it still have the hose connections or have they been cut off and tapped for male fittings?

[Jim Brock]

no name has std hose fitting in it, it looks as if they can be taken out

[napabob]

Jim,
Updated image with a washing and steel wool touch up. Still needs some fine polishing.
I do not want to remove the hose connections on your top, but I do want to confirm that the Nicson top that I want to use will fit your Neovane V-105.
http://www.hotboatpics.com/pics/data/500/6782WaterPumpTopFront2.jpg
Do you have a PayPal account to request funds?

[napabob]

I purchased a Neovane water pump and the 1" diameter inlet/outlet matches the Nicson water distribution top. The exception is that the Neovane water pump does not have the 1" NPT female threads to accept the Nicson base plate assembly.
I am again looking for a match to the top as posted, which woudl be a Nicson pump. I have read posts here on Nicson water pumps, but they are for mid 2006, any leads will be appreciated.

[Jim Brock]

should have bought mine complete!!! I don't think nicson made a top like the one you have for the smaller pump.

[napabob]

should have bought mine complete!!! I don't think nicson made a top like the one you have for the smaller pump.
Jim,
The one I purchased from eBay is complete with two impeller replacment kits ($31.00 value each +/-).
I paid $85.00 plus $10.00 shipping for the Neovane V-105.
There is a Nicson top for the small Neovane 8 screw (Now listed on eBay). It has been altered, the top hose inlet and outlet have been cut off and threaded for male fittings.
http://i4.ebayimg.com/06/i/000/90/ag/9c8d_1.JPG

[napabob]

to the top

[Rexone]

Hanly made the V105 Neovanes both with threaded inlets that will accept the Nicson style top, and without threads that accept the Hanly manufactured divider that bolted on. The top Hanly made was brass chromed.

[napabob]

Rexone,
I must have the Hanly water devider top and matching Neovane water pump. It only uses two rubber washers and it bolts on to a threaded plate inserted into slots on each side of the inlet and outlet on the pump.
I am still searching for a V-105 with female threads to match my Nicson top.
Bob
http://www.hotboatpics.com/pics/data/500/6782Hanly3.jpg
http://www.hotboatpics.com/pics/data/500/6782Hanly2.jpg
http://www.hotboatpics.com/pics/data/500/6782Hanly.jpg

[Rexone]

http://www.hotboatpics.com/pics/data/500/6782Hanly2.jpg
The divider on the left is the brass chrome one that Hanly made that bolts on (non threaded pump).
The divider on the right (Nicson) requires the Hanly (Neovane 105) that was threaded. You could use the threaded pump with the Nicson divider or some just ran a fitting in and out down to a separate tee depending on needs.