BBC w/ Lightening headers for sale

[CcanDo]

Standard bore 454, JE pistons, dimple rods with ARP bolts, std GM steel crank, 4 bolt block, GM 990 heads, Comp Cams solid roller, Comp Endur-X lifters, Comp Stainless roller rockers, polished Offenhouser single carb tunnel ram, Braaswell prepped 850 Holley, MSD Distributor, MSD 6M-2 box, MSD rev limiter, Canton pan, blueprinted Clay Smith oil pump. Motor has 72 hours, runs very good, starts good, sounds good, and has been unbelievably reliable. Includes Lightening jacketed headers, starter, alternator - everything needed to bolt in your boat and go to the lake. $5800.00
Full Lightening rail-kit with belhousing and motor plates available if needed for additional $500. If interested, please reply to Email and I will phone you with additional information. Pictures on the way.

[gr16241]

Interested in selling the Lightning headers seperate from the motor?

[condor tx 19]

will you sell the rail kit seperatly and do you have a pic of it?

[Burn504]

Interested in selling the Lightning headers seperate from the motor?
also interested

[Skip3]

Is this the motor out of the sleekcraft, I was just talking to Garry Snow about that boat.If so those headers would look really good in my sst and I know they would fit....................

[CcanDo]

Thanks for the interest. This is the motor out of the Sleekcraft. I would like to sell everyting as a package, but make me an offer and if it makes sense I will part it out. Sorry no pictures yet, they will be posted tomorrow.

[CcanDo]

Pics

[El Prosecutor]

Pics
http://www.***boat.com/forums/attachment.php?attachmentid=36664&d=1186543047
Posting Pics :) (http://www.***boat.com/forums/showthread.php?t=154406)

[CcanDo]

Thanks for enlarging the pic - havnt figured that out yet.

[CcanDo]

OK, lets split it up. $4800/motor $800/headers $offer/rail kit, belhousing, etc
Motor is turn-key, drop in and go.

[Skip3]

Ok you got my interest on the headers you have any pics of them in the boat so I can see how they were run??? I know our hulls are the same But I would just like to see.
Why you tearing your boat apart ?? I loved that boat
you can email pics to cheppard@stx.rr.com

[ZRCTION]

you peaked my interest in your motor. What are the hp/torque #'s. Looking for a motor for my flatbottom.

[CcanDo]

You know, I am the worlds worst about taking pics - I really don't think I have any, but I will look. In the meantime, I can put them together on the pallett so you can see them together.
I have not dynoed this motor, but it turned a B impellor in a tight pump 5800 rpm. Maybe someone on the forum has the chart to give an idea of power. The motor has 10.3 compression with good heads and valvetrain - somewhere between 500 - 600 HP is my guess. The pictures are really unfair, the intake is very polished, headers are shiny, etc.

[396_WAYS_TO_SPIT]

You know, I am the worlds worst about taking pics - I really don't think I have any, but I will look. In the meantime, I can put them together on the pallett so you can see them together.
I have not dynoed this motor, but it turned a B impellor in a tight pump 5800 rpm. Maybe someone on the forum has the chart to give an idea of power. The motor has 10.3 compression with good heads and valvetrain - somewhere between 500 - 600 HP is my guess. The pictures are really unfair, the intake is very polished, headers are shiny, etc.
I would say that this motor is 600hp per hi-tech's chart.....
http://www.hi-techperformance.com/images/Impeller_Chart.jpg

[CcanDo]

Thx for posting the chart.

[gr16241]

Could you measure the width of the pipes at their widest point on the motor and let me know. They will probably be either 33" or 36". Thanks

[corrupted cat]

:) all go 1.000 for lighting headers get me at www.fatcatdaytona@netzero thanks mike any time

[ZRCTION]

OK, lets split it up. $4800/motor $800/headers $offer/rail kit, belhousing, etc
Motor is turn-key, drop in and go.
How much is shipping from Texas?
I don't need the headers, does it come with everything else? Carb, pan, ign...?

[gr16241]

Are the headers still for sale? Email grant@mitchscarpet.com - Thanks

[CcanDo]

Sorry for the late response. I think headers measure 33" , but will measure tomorrow and post dimensions here. Headers are still available as is the motor.
Motor is complete including ignition, alternator, starter, fuel manifold/carb, thermostat, etc. Everything in pictures is included except motor mount parts (ie. rail kit/drive line guard/belhousing/motor mounts) $500 extra if you want all of these items. Based on the last engine I shipped (New York to Texas) I expect it to cost very close to $600 Texas to Cali. The motor will be mounted inside a wood crate for transport. I am amazed no one has jumped all over this. This motor has never been hurt in any way; everything is standard so no junk parts surprises, and totally complete ready to run. Very reliable pump gas motor making very respectable power. Will take 2 days to crate and ship.

[CcanDo]

After measuring this morning, the headers do in fact measure 33" at the widest point.

[PLACECRAFT20]

Is that my black motor in the background? I also talked to someone you raced with the Placecraft that wanted my stock motor. Good luck with the sell.

[CcanDo]

Thanks Mitch. Yes, that is your motor in the background. If you look close, you can see that there are two sitting side-by-side. This motor I am selling came out of the SleekCraft tunnel. I am really surprised no one has snatched this up - it will really make someone a nice package for the money. Let me know when you want to come look - Oh, and bring that gel cell battery when you come:)) John

[Outlaw]

what do you want for the rail kit with front plate,
flywheel cover and driveline guard?

[CcanDo]

I would like to sell it with the motor. I really don't have any idea what is worth - can't remember what I paid. Make me a real offer and I might split it up. There is not a single scratch on any of it and anodize is not faded at all.

[gr16241]

PM sent

[PLACECRAFT20]

Hey John,
Gell Cell was dead. I had to take that one out of the Eliminator to bring to you. I guess I let it sit to long without a charge. I took the one out of my Golf cart for the Eliminator. I still need to buy one.

[CcanDo]

No worries. I had a spare - just givin you a hard time.:)

[gr16241]

PM sent

[CcanDo]

Thursday bump

[CcanDo]

Headers are sold. Motor and rail kit still available.

[gr16241]

Thanks John,
I look forward to receiving the headers. Someone needs to buy this motor!

[gr16241]

Saturday Bump

[CcanDo]

Thanks Grant. I am really surprised the motor has not sold.

[CcanDo]

bumpy

[CcanDo]

back to the top:)

[CcanDo]

OK - Lets try $4500. Come on guys, you cant build a motor for this. No surprises. This motor is a turn-key drop in.

[CcanDo]

Motor and rail kit still available.