Longstr
08-28-2007, 05:27 PM
I have owned this boat for a year and it spent most of its time being redone including:
New custom designed subfloor support
New floor fiberglassed 3/4 in Ply
New stringers
New Marine Carpet
Custom seats made from fiberglassed plywood designed after a Taylor Sj, Marine foam for seats was from Ultimate interiors, and Skins were designed by me and sewn by XOTIC concepts in Lincoln Ne. I also made the rear seat to allow for flush mounted 6in JBL marine speakers.
All new Beede Gages, anadized beezels, steering hub, and steering wheel, anadized push pull switches ( Int, Ext, Bilge, Nos, Dash) No NOS has been hooked up to motor, I had planned on it but never got that far.
I have made a custom Aluminum Ride plate set at 5 degrees up it is 4 in longer than stock, and 1 in narrower to help air the boat out.
I put a new water seal kit in the Panther jet along with a bushing kit to tighten up the linkages, the pump runs perfect.
The 360 AMC is a strong runner turn key it has never failed to start for me it was freshened up 2 seasons ago by previous owner.
Holley Marine 750 vac sec carb
Edelbrock RPM intake
Comp cam, has a mild grind
I put on a Pro Comp electric Fuel pump to keep a constant 7-8 psi of fuel flowing to the motor.
All new water lines, hoses, plugwires, battery, and charging system.
I runs 59.2 on GPS @ 4800 RPMs
Call Ryan @402-440-8402
Or email @ longstr80@yahoo.com
I have hundereds of pics pre, during, and post build. More than happy to email all you want
http://i150.photobucket.com/albums/s101/longstr80/DSCN0785.jpg
http://i150.photobucket.com/albums/s101/longstr80/DSCN0784.jpg
New custom designed subfloor support
New floor fiberglassed 3/4 in Ply
New stringers
New Marine Carpet
Custom seats made from fiberglassed plywood designed after a Taylor Sj, Marine foam for seats was from Ultimate interiors, and Skins were designed by me and sewn by XOTIC concepts in Lincoln Ne. I also made the rear seat to allow for flush mounted 6in JBL marine speakers.
All new Beede Gages, anadized beezels, steering hub, and steering wheel, anadized push pull switches ( Int, Ext, Bilge, Nos, Dash) No NOS has been hooked up to motor, I had planned on it but never got that far.
I have made a custom Aluminum Ride plate set at 5 degrees up it is 4 in longer than stock, and 1 in narrower to help air the boat out.
I put a new water seal kit in the Panther jet along with a bushing kit to tighten up the linkages, the pump runs perfect.
The 360 AMC is a strong runner turn key it has never failed to start for me it was freshened up 2 seasons ago by previous owner.
Holley Marine 750 vac sec carb
Edelbrock RPM intake
Comp cam, has a mild grind
I put on a Pro Comp electric Fuel pump to keep a constant 7-8 psi of fuel flowing to the motor.
All new water lines, hoses, plugwires, battery, and charging system.
I runs 59.2 on GPS @ 4800 RPMs
Call Ryan @402-440-8402
Or email @ longstr80@yahoo.com
I have hundereds of pics pre, during, and post build. More than happy to email all you want
http://i150.photobucket.com/albums/s101/longstr80/DSCN0785.jpg
http://i150.photobucket.com/albums/s101/longstr80/DSCN0784.jpg