WTB BBF 460 .030 over pistons

[2savage4you]

Im looking for some .030 over pistons for my build at a good price :D
BBF 460 .030 = 466=:devil: Oh YA this is my first Ford build and i wanna do it right, Can anyone recommend a good piston for a boat engine? Or better yet have some for sale
2sav

[76miller]

I have 7 good ones. They are forged TRW's(rods included). I will give you a smoking deal if you want them for your build. PM me.

[2savage4you]

I have 7 good ones. They are forged TRW's(rods included). I will give you a smoking deal if you want them for your build. PM me.
Pm sent.
2sav

[Squirtcha?]

I've got a set of these (8). Speedpro .030 over forged pistons with a -22cc dish. These came out of a running motor and are in good shape. Although they'll work, I probably wouldn't recommend using them with the larger chamber heads 97cc as your compression ratio would end up being approx 8:1 and a little on the low side (the buddy I got the short block from had this combo 97cc D3 heads). The motor ran fine, but I think it would've been much spunkier with a little higher compression ratio.
They would work great with a 72-77cc head though. Compression ends up being around 9.5:1 Makes for a nice safe pump gas combo. I've got a set of these same pistons in the motor I'm running now.
The pistons are still on the connecting rods and I'd let them go as well.
$150 bucks for the whole works. My plan is to build this motor as a stroker so I'll be getting different pistons and connecting rods with the kit.
If you're at all interested I can put up some pictures of the actual parts.
Here's a link to the advertisement from Jegs.
Speedpro .030 overbore 22cc dished pisons forged (http://www.jegs.com/webapp/wcs/stores/servlet/product_10001_10002_40918_-1)
460ci Stock-Type Piston, .030'' Overbore
Piston Dia.: 4.390''
Piston Top: -22cc Dish
Pressed Pin
Comp Ratio: 9.79:1 w/72cc Heads, 8.01:1 w/97cc Heads
Ring Grooves: 5/64'', 5/64'', 3/16''
Sold as Each $42.99
844-L2404F30
http://www.jegs.com/images/photos/800/844/844-L2404F30.jpg

[2savage4you]

Wow thats a good price yes please post pics:D
I will be running D3's A2A which i think are 91.4 cc's:idea:
2sav

[Squirtcha?]

Sorry I screwed up in the above post I put down D1VE
which are block numbers not heads. I meant D3 A2A cylinder
heads. I think you'll find that they're actually 97 cc chambers
on those heads.
If you look at the advertisement it shows the compression with
97 cc heads and that would be the ones that you're going to run.
Like I said, they'll work fine and the motor that they came out of
had D3 heads. Compression will be around 8:1 like I stated earlier.
I didn't even clean em up. I just pushed em out of the holes and
boxed em up.
Here's some photos.
http://www.***boat.com/image_center/data/500/Pistons_rods_A.jpg
http://www.***boat.com/image_center/data/500/Pistons_rods_B.jpg

[Squirtin Thunder]

Those are the ones I need, but I only need one. Steve that is the same as what was in my engine but I had 70cc chambers.

[Ralph Brunt]

Those are the ones I need, but I only need one. Steve that is the same as what was in my engine but I had 70cc chambers.
get these and get your ass to parker:devil:

[2savage4you]

Will these work with a 4.140 crank and 6.800 rods? are the pins pressed cause i need to float the pins with the new rods:D
2sav

[Squirtcha?]

They are press in pins. You'd end up with about 500 cu in. Not sure what your question
is regarding the crank and rods though. Will it fit? Yeah. Guess it doesn't really matter
since you don't want the press in pins anyway.
Those are the ones I need, but I only need one.
Steve that is the same as what was in my engine but I had 70cc chambers.
Just think Jim......you'd have 7 spares pistons and 8 spare rods. Don't think you'll find
a better price.

[2savage4you]

They are press in pins. Not sure what your question is regarding the carnk and rods
though. Guess it doesn't really matter since you don't want the press in pins anyway.
Just think Jim......you'd have 7 spares pistons and 8 spare rods. Don't think you'll find
a better price.
Ya i guess i didnt explain, I just bought some H beam rods that are 6.8 and a stroker crank. The H beams are bushed for a floating pin, this is why i asked:D and was wondering if they would still work now that its stroked:idea: Never did a stroker before so i just had to ask. So i take it they wont fit now:confused:
Well this is a hell of a deal, Jim you should buy them and have some extras.
Thanks,
2sav

[Luckie Stiff]

Hey Squirtcha, check your PM's :D

[pw_Tony]

Hey Squirtcha, check your PM's :D
You're too lucky.... and too stiffy.... and your post count is too low...
Damn Ford guys lol, ;)

[Luckie Stiff]

You're too lucky.... and too stiffy.... and your post count is too low...
Damn Ford guys lol, ;)
WTF does my post count have to do with anything?:idea:
If Steve isn't interested in these, I am.
Seems simple enough.

[pw_Tony]

WTF does my post count have to do with anything?:idea:
If Steve isn't interested in these, I am.
Seems simple enough.
Just messin with yah Comrad... see yah on that "other" site ;) :D