PDA

View Full Version : I think its broken



68campbell
02-10-2003, 11:33 AM
The engine was running a little rough http://www.sieversburnett.com/ouch.jpg

Blown 472
02-10-2003, 11:35 AM
Cylinder wall thickness check?

miller19j
02-10-2003, 11:42 AM
JB Weld..... wink

HavasuDreamin'
02-10-2003, 12:04 PM
Duck Tape wink :p :D

Jordy
02-10-2003, 12:10 PM
The JB Weld is the way to go in this case... fill it, grind it and call it good to go, into somebody elses boat. :D

Blown 472
02-10-2003, 12:14 PM
And just how well does the disco wagon run???

Jordy
02-10-2003, 12:17 PM
You talking about Miller's Disco Pimp Schiada? :D

Havasu Doug
02-10-2003, 12:20 PM
68campbell:
The engine was running a little rough http://www.sieversburnett.com/ouch.jpg Is that something growing in there? :confused: :D

Thunderbutt
02-10-2003, 12:35 PM
He had Grass in his Gas

Liberator TJ1984
02-10-2003, 12:38 PM
Leave the slug outta the hole just opposite that one ...she'll smooth right out :D
Gopherrr

JetBoatRich
02-10-2003, 12:51 PM
I would go ahead and get the upgrade with the whole cylinder wall. wink

24RODjr
02-10-2003, 12:57 PM
Thunderbutt:
He had Grass in his Gas ...Nobody rides for free... :D

superV
02-10-2003, 12:58 PM
So how much for that bad boy? I need a new race block! :D wink

spectratoad
02-10-2003, 01:24 PM
Can't you just slide an empty silver in there and call it good? :D

68campbell
02-10-2003, 02:34 PM
The damage started with a snapped strut. Motors don't enjoy going from 6k to 0.
[ February 10, 2003, 02:37 PM: Message edited by: 68campbell ]

ACCEPTENCE
02-10-2003, 07:53 PM
68campbell:
The damage started with a snapped strut. Motors don't enjoy going from 6k to 0. Ouch, that dose'nt sound so pretty...

Hal
02-10-2003, 08:57 PM
Looking at that crank I would say it was time for a little up keep anyway.

93eliminator
02-10-2003, 09:19 PM
I knew i should have stayed with the 100 hp NOS system instead of the 250hp. :D

68campbell
02-11-2003, 08:51 AM
Crank is rusty because the block has sat outside since May. (Crank is broken about 2" above the cylinder)

DansBlown73Nordic
02-11-2003, 10:54 AM
Was it making a funny Noise? :D

JetBoatRich
02-11-2003, 10:58 AM
Maybe you can use some of that tape mentioned on the other thread :p

HalletDave
02-11-2003, 11:00 AM
Oh nooooo. eek! :rolleyes: It's that JetBoatRich guy again! :D
HD

JetBoatRich
02-11-2003, 11:51 AM
HalletDave:
Oh nooooo. eek! :rolleyes: It's that JetBoatRich guy again! :D
HD What do you say BROTHER

68campbell
02-11-2003, 12:30 PM
It made a slight grinding sound, almost like a jet ski or nails on a chalkboard or the wife mentioning free gift with purchase.