WHAT HEADS TO GET.

[Hallett]

I HAVE A 468 WITH A 871 TBS BLOWER. WHAT KIND
OF HEADS SHOULD I GET I HAVE THE VALVES BUT
DONT KNOW WHAT HEADS WOULD BE THE BEST FOR
MY SET UP. THANKS GUYS.
[ January 31, 2003, 06:44 AM: Message edited by: HALLETT ]

[DogHouse]

If you believe the various companies' claims and advertising, it would seem that AFR is outflowing everybody else these days, especially their CNC ported versions. Their websight (http://www.airflowresearch.com) has a link to a flow comparison with most of the popular heads. Prices are reasonable, <$2k for the basic package with valves and roller springs, <$3k for the full CNC ported versions. They have several different runner sizes, one of which should match your setup. I haven't tried their big block heads yet, but I did run their small block heads for a while and was very happy with them.
-brian

[Liberator TJ1984]

I wanted to buy a set of their 345 runners as cast for $1995.00 but they are on hold due to casting setbacks .They won't be out for another 3-6 Months cry ??? the 357 CNC are ready and they cost $3200.00 and take about a week delivery... :D
oh yea they come with Ferria valves and all good parts but you can upgrade to titanium ret. and such for a minimal $$$$
[ January 28, 2003, 09:45 AM: Message edited by: Liberator TJ1984 ]

[Clown]

Set Of Ray Franks
PRO Filer Heads
Stece schimdt sell's them and there worth looking into!!!!!!!!!!!
Steves #####1-317-890-7178
He's $200.00 cheaper than the other's

[SPECTRABRENT]

What do you guys think about Dart Pro 1's?
Brent

[MikeF]

Clown:
Set Of Ray Franks
PRO Filer HeadsAWESOME heads!, but a little overkill for a 468 wink .

[Fiat48]

I like Brodix. Take a look at BB2-Xtra. http://www.brodix.com/onlinecatalog/page1-2/page1-2.html

[Clown]

MikeF:
Clown:
Set Of Ray Franks
PRO Filer HeadsAWESOME heads!, but a little overkill for a 468 wink . Ya I know but I figure I'd Tell a person that is looking to Buy a new set of heads. That the
Pro Filers Are what you want. Because We all no that next year we are going to want to go faster and build a bigger motor. Trust me , I've been there more than a couple of times .Build a big Cubic Inch motor "O"
And now I need the heads that Will match my new setup
The process starts all over again Get the ,
,Jesel
,Ferrea
,PSI Springs
,Titanium Retainers
The list goes On And ON
And two seasons Later, Start at square one again! smile_sp
I lookd at that statement about heads to buy!
And totally forgot My mannors. :rolleyes:

[Craig]

Fiat48:
I like Brodix. Take a look at BB2-Xtra. http://www.brodix.com/onlinecatalog/page1-2/page1-2.html That's the heads the shop we use recommends

[Hallett]

HEY GUYS JUST WANTED TO SAY thanks FOR ALL THE INFO
ON THE CYL HEADS I FOUND A GUY THAT SELLS DART PRO
ONE HEADS .BARE FOR 1345 A PAIR. AND COMPLETELEY
CNC PORTED FOR 2157 A PAIR any SIZE . HIS NUMBER
IS 765 525-4825 ASK FOR ROGER WILLIAMS.SOUNDS PRETTY GOOD. LET ME KNOW WHAT YOU GUYS thanks.
[ January 31, 2003, 06:50 AM: Message edited by: HALLETT ]

[Liberator TJ1984]

Buy once ! I've called just about everyone and told them what I am running...454 8/71 they have told me to go with 345 runners or up w/CNC
job ...don't think your overkilling here ???

[Clown]

I have been told that those Dart Pro-1
Are not a good Idea if your Planning on putting alot of boost to the motor, Because the casting are "How do I say Kinda Cheap" There not as thick as lets say the regular old Dart 360
For a Pair of bare Pro filers I think the Price was Around $1700.00
I know The price for the cnc'd fully assembled
ones was around $3.300.00
DID YOU CALL STEVE SCHMIDT?? jawdrop

[Liberator TJ1984]

Jah I did ...still comparing $ and #...How much for the Z-28 in the pic.of turbos????? smile_sp

[Clown]

Just The Turbo;s
And $8,000.00

[Hallett]

Clown:
I have been told that those Dart Pro-1
Are not a good Idea if your Planning on putting alot of boost to the motor, Because the casting are "How do I say Kinda Cheap" There not as thick as lets say the regular old Dart 360
For a Pair of bare Pro filers I think the Price was Around $1700.00
I know The price for the cnc'd fully assembled
ones was around $3.300.00
DID YOU CALL STEVE SCHMIDT?? jawdrop