flat broke
06-06-2004, 12:02 AM
Thanks to Mike at Rex, I was able to have my Olson cooler checked out/gone through so that I could sell it with confidence that it would serve its new owner well.
The cooler body/end caps was powdercoated gloss black prior to its trip to Olson to ensure it looks good for many seasons to come without the hassle of keeping it polished.
http://i1.ebayimg.com/02/i/01/f0/2d/1c_1.JPG
http://i1.ebayimg.com/02/i/01/f0/2d/2a_1.JPG
http://i1.ebayimg.com/02/i/01/f0/2d/2a_1.JPG
Check it out on Ebay at http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2481435018
Buy it now on Ebay is set at $300, but I'll let it go at $280obo if you pm me through the boards. Check it out new at $525 at Rex.
Next up is the billet flame arrestor/air filter I had made for when I was going to run a single carb on the new motor. Well, there's going to be two carbs now, and as such I don't need this paperweight in the garage anymore. When Hack Job dyno'd his BBF last month he gained 2hp over open carbs using a K&N based flame arrestor similar to this one. This one is set up for a Holley/Edlebrock/Carter std carb and is ready for polish/powdercoating/anodizing. I have it at $60 on Ebay, grab it up for $50 via PM.
http://i9.ebayimg.com/01/i/01/ed/87/21_12_s.JPG
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=31286&item=2481434632
Arrestor is sold!!!
PM me with any questions as I've been having some problems with my email lately.
Thanks,
Chris
The cooler body/end caps was powdercoated gloss black prior to its trip to Olson to ensure it looks good for many seasons to come without the hassle of keeping it polished.
http://i1.ebayimg.com/02/i/01/f0/2d/1c_1.JPG
http://i1.ebayimg.com/02/i/01/f0/2d/2a_1.JPG
http://i1.ebayimg.com/02/i/01/f0/2d/2a_1.JPG
Check it out on Ebay at http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2481435018
Buy it now on Ebay is set at $300, but I'll let it go at $280obo if you pm me through the boards. Check it out new at $525 at Rex.
Next up is the billet flame arrestor/air filter I had made for when I was going to run a single carb on the new motor. Well, there's going to be two carbs now, and as such I don't need this paperweight in the garage anymore. When Hack Job dyno'd his BBF last month he gained 2hp over open carbs using a K&N based flame arrestor similar to this one. This one is set up for a Holley/Edlebrock/Carter std carb and is ready for polish/powdercoating/anodizing. I have it at $60 on Ebay, grab it up for $50 via PM.
http://i9.ebayimg.com/01/i/01/ed/87/21_12_s.JPG
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=31286&item=2481434632
Arrestor is sold!!!
PM me with any questions as I've been having some problems with my email lately.
Thanks,
Chris