Page 1 of 9 12345 ... LastLast
Results 1 to 10 of 84

Thread: "ONCE AGAIN" PARTS SWAPMEET- The 2005 Season!!!!!!

  1. #1
    396_WAYS_TO_SPIT
    Ok since I always start a one for "us" budget boaters I will start a new one.This will be the 2005 season swapmeet. Please go through all of your stuff. I know we all have parts laying around. Some people need things that some of us arent using. Besides, the money can go to a good cause like gas and beer
    396
    I will start it with this
    I have a set of BBC "Rewarder" thru transon headers. They are chrome with some blueing. They have very minimal rust between the pipes. They also have water lines with them. There is no dents or dings on them at all. I have a product that can remove the blue on them. I will take $400 for the pair plus shipping.--------SOLD!!!!

  2. #2
    wideopen545
    http://www2.***boat.com/image_center...17DSC01040.JPG
    bbc upsweep headers coated with clappers 350.00 & shipping
    a set of k&n v stacks with new filters for 4150s 100.00 & shipping
    a fresh .030 454 2 bolt cam bearing and brass plugs installed
    all parts are new still in boxes all you need is pistons ring and bearings
    cast crank 10r/20m ready to install
    large oval heads open chamber 049 cast
    manley sever duty 2.250 int and 1.88 ehx new in box
    comp solid cam with springs and lifters new in box
    weind team g intake new in box
    mildon oil pan new in box
    all parts are new in box
    2000.00 & shipping or can deliver up to 300 mi
    set of auto meter guages 2 1/8 white face temp and oil 40.00
    rex hot foot with cable 75.00 & shipping
    barry grant hr 280 fuel pump fresh from berry grant 150.00 & shipping
    set of k&n 4500 v stacks new 65.00
    4500 INLINE or sideways BLOWER TOP 2 X 4 100.00
    mini starter for bbc or sbc nice 100.00 & shipping
    AT IMPELLER NEW A-2 CUT STD/STD ON THE WEAR RING SIDE 215.00 P/SHIPPING
    edelbrock torker II oval port intake 125.00 p/shipping
    v-drive timing cover with pump drive and water inlets 75.00 p/shipping
    full face helment w/shield and d rings installed snell 95 /dot size x/large white with blue stripes 100.00 p/shipping
    gm-hei std deck bbc distributor two coils one white wire coil and one yellow wire coil 75.00 p/shipping
    bbc moroso valve covers tall chrome 30.00 p.shipping
    more parts to come
    tim 540.871.4833

  3. #3

  4. #4
    steelcomp
    (1) 460 Ford + .030 D1 block fully deburred and casting flash removed, L2404 forged pistons and moly rings, polished truck/CJ rods w/ARP bolts, stock 460 crank 10-10 w/ Clevite brgs, precision balanced, (1) C8VE, and (1) D0VE head, stock valves, screw in studs, Isky 5/16 pushrods and guide plates, Isky chromoly retainers, Boss 351 adjustable rockers, poly locks. Melling hydraulic torque cam, 490"/515" and 204/214 @ .050". Cloyes true roller, Truck rear sump pan w/ stock oil pump. M/T finned alum. valve covers. Will consider cam/spring change. Will add intake and/or roller rockers for extra...zero time since freshen....$3500.00/ offer.
    (1) 467 BB Chev (buyer backed out) four bolt, steel crank, Eagle rods, Cosworth pistons, 990 heads-ported, cc'd, 2.25/1.88 Manley ProFlo, Crane Gold rockers, Isky springs, Ti. ret's, Manley pushrods, solid flat...610 lift, 264 @ .05. Dooley 10qt jet boat pan, ARP head, main, and rocker studs, Weiand Pro Ram, ported and matched, sideways mounted 800 Holleys. This is a professionally built motor with less than break in time on it. 650-670 hp. (more details avail.)
    $5500.00 carbs to pan.
    (1) set, import stainless one piece int. valves, 2.25 X 3/8 stem std. length for BB Chev...new...$75.00
    (1) set, Comp Products Severe Duty intake valves (comparable to Manley) 2.25 X 11/32" stem w/ 27 deg. backcut. Stock length for BB Chev. ..new...paid $21.95 ea. (before backcut)...$125.00
    (1) set...Howard Congo Pro Alloy roller springs, cups, and Trick Ti. retainers, new, never assembled. Springs are 1.550" dual, 230#@1.88, 650#@ 1.15, cb@ 1.08
    Springs new were 149.95
    Retainers were 119.95
    Cups were 42.95
    Total new was 312.85. Sell for 250.00
    (1) Lunati solid roller...722", 272/280 @ .05 new, never out of box. $250.00 Works with above spring/ ret. assy.
    (1) pair Ford C4AE Big Port FE heads. No sunk valves, good condition. These are listed as one of the best choices for factory iron FE heads...used... $300.00/ offer.
    (2) Ford 351C solid cams Crane grind no. F246/3294-2-8 (246/256@ .05"/.570/590")
    F286/3823-8 (286@.05"/.672)
    both new, never used...$125 ea...both for $200.00
    (1) Cast iron 429 CJ intake manifold...used...$150.00
    I accept cashier's check or PayPal
    PM me if interested in anything.
    More to follow.
    __________________

  5. #5
    AJ
    Tim
    I am interested in your v-drive timing cover with pump drive and water inlets 75.00 p/shipping, sending me some pics.
    Thx.AJ

  6. #6
    Ken F
    3 month old Holly 4150 Marine 750 DP. Airhorns have been worked by HTP $500
    Jomar Stud Girdles-429/460
    Tall Aluminum Ford Racing valve Covers, good shape
    Mallory Pertronix "optical-eye" distributor almost new,in box
    Fits 429/460 Comes with either bronze gear, or steel.
    Mallory Dual point dist. 429/460
    460 Ford p/u rear sump pan, pickup tube, and almost new Mellings oil pump
    Complete Jacobs electronic ignition, w/Jacobs plug wires
    1 set of small (bolt adjustable) ride-plates
    PM for prices

  7. #7
    Taylorman

  8. #8
    taylormanss
    Complete Jb pump with splitbowl 400.00+ shipping ,two bucket seats need recovered,but are all plastic inside,foam is still good 150.00+ shipping,rock grate 40.00+ shipping,4 fiberglass buckets low back with covers 200.00 + shipping,hot foot throttle 40.00+shipping,1 set of bassett over transom headers dry exhaust 75.00 + shipping. taylormanss@yahoo.com

  9. #9
    mexrunner
    needed asap just pulled heads off motor and had two broken pistons & a cracked cylinder. :frown: so i need a big block chevy 454 block only perfer 4 bolt but we consider all older brother is comeing down on block leave memorial day and had a river trip planned and dont want to cancel on him. Thanks Adam

  10. #10
    CARLSON-JET
    BBC Brodix 2-X Reher Morrison Alum. heads. Pro ported and hand blended. New New Vasco-Jet Roller tripple Springs .800"+ lift, 2.30 int. 1.88 exh. SS Manley 11/32 severe duty valves, Comp cams guide plates, new guides, seals, retainers & keepers all top shelf parts. Intakes flow 384 cfm @ .750. Heads are fresh and wrapped up. these are ready to run and in as new cond. never been damaged. Matching polished Alu V/Covers w/ Reher Morr. insignia set up for vacuum pump & polished. R/M pushrods to match. flow numbers lift IN EX .200 154 157 .300 222 201 .400 286 233 .500 324 258 .600 360 275 .700 380 286 .750 384 288 .800 385 292 and many pics. Port work and machining done by Performance Motorsports, Tim Merchant in Sandwich, IL. As you can see these heads are spotless. All surfaces are perfect. can answer any questions about these. E-mail me @ robnbek2u@aol.com for any add info.or Call (815)363-0953 $3200 invested asking $2200 for all obo.Thank you R.B. http://www.hotboatpics.com/pics/data...C00028-med.JPG
    http://www.hotboatpics.com/pics/data...ber_2X-med.JPG http://www.hotboatpics.com/pics/data...C00033-med.JPG http://www.hotboatpics.com/pics/data...C00029-med.JPG

Page 1 of 9 12345 ... LastLast

Similar Threads

  1. PARTS SWAPMEET-Once again!
    By 396_WAYS_TO_SPIT in forum Jet Boats
    Replies: 249
    Last Post: 11-21-2004, 06:43 AM
  2. Parts Swapmeet?
    By cyclone in forum Jet Boats
    Replies: 87
    Last Post: 07-11-2004, 09:44 PM
  3. Another PARTS SWAPMEET!!!!!!!!!!!!!!
    By 396_WAYS_TO_SPIT in forum Jet Boats
    Replies: 69
    Last Post: 04-30-2004, 08:08 AM
  4. PARTS SWAPMEET-EVERYBODY WITH PARTS PLEASE POST
    By 396_WAYS_TO_SPIT in forum Jet Boats
    Replies: 249
    Last Post: 02-03-2003, 11:05 PM
  5. PARTS SWAPMEET...EVERYONE WITH PARTS PLEASE POST
    By NashvilleBound in forum Boating, West
    Replies: 17
    Last Post: 11-14-2002, 05:45 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •