Results 1 to 7 of 7

Thread: info. on cam,lifters, rocker arms, timing chain set

  1. #1
    Big-Tex
    Could use some input please. Here we go try not to get bored. 454 chev. 72-79 model 2-bolt. Heads are 69model 396 closed ovalport. 10:1. TRW-pistons L2377 .030 over. Intake is Edlebrock TM2-0, maybe called a tarantula. HEI distributor vacum adv. Holley carb. 750 double pumper. Oh yeah, boat is 76 model 18ft. sleekcraft closed bow. berkeley pump 12jb-a. This is first jet to rebuild. Have had a v-drive before with smallblock.Thanks

  2. #2
    77charger
    Try a comp cams 280 or 292 magnum.With your comp ratio and intake this will be a good match for 5k-5500rpm.Get the proper springs too.I ran this similar set up in my 71 camaro bbc 396 car ran 12.20s@108.I would consider this a reliable set up too.This was my only exp with bbcs as my current boat motor is an 11-1 bbf 429 with similar cam specs too but i am running a b+ impeller to get the motor to the upper rpm range.head porting is on the way.

  3. #3
    nastyhabit
    call comp cams they will sugest combos to you, tell them its a BOAT not a car they might want to know the weight of the boat also,comp cams are good i had a close combo of 77 charger in my 701/2 Z28 rally sport didnt loose much had a great kakle in one month got pulled over 14 times in the city of orange and not one ticket but i had dust on the plates one of the two lites above the plates were out so dont drive your boat in orange just a warning-o-ya try to off the 750 and get a 850 dbbl pump---nasty

  4. #4
    Cas
    nasty's right, give comp cams a call and they'll give you the scoop on what you need.

  5. #5
    DOHARA
    BIG TEX, try this,
    [img] http://www.compcams.com/catalog/106_107.jpg
    [img/]
    Im running the 11-244-4 in my BBC with merlin heads and 10:1.1 comp runs great. That chart should help with your choice.
    DANO

  6. #6
    396_WAYS_TO_SPIT
    HEY BIG TEX, I AM RUNNING A SIMILAR SET UP AND I NEED SOME IDEAS ALSO. I HAVE A BBC 454 W/ 850 DOUBLE PUMPER, AND THE CAM I PICKED IS SIMILAR TO THE THE ONE CHARGER IS USEING. MY IS GOING TO BE PART # 11-336-4. IF YOU GET IDEAS PLEASE EMAIL ME AT MRFIERMAN78@HOTMAIL.COM WE CAN WORK TOGETHER AND HELP EACH OTHER.

  7. #7
    wsm9808
    Where is Vernon? I,ve been through there but I cant remember which part of the state it is in. Any where near Del Rio? There is a jet boat gettogether forming for Memorial week end at Amisted.

Similar Threads

  1. Rocker arms
    By FlatRat in forum V-Drives
    Replies: 7
    Last Post: 08-17-2005, 02:14 PM
  2. rocker arms
    By Nucking futs in forum Gear Heads
    Replies: 12
    Last Post: 09-08-2004, 07:42 PM
  3. Which rocker arms???
    By 396_WAYS_TO_SPIT in forum Gear Heads
    Replies: 18
    Last Post: 02-15-2004, 10:31 PM
  4. 1.7 to 1.8 rocker arms
    By slotracer in forum Gear Heads
    Replies: 9
    Last Post: 01-16-2003, 12:26 PM
  5. 1.5 TO 1.6 ROCKER ARMS
    By BOBBY MC in forum Gear Heads
    Replies: 11
    Last Post: 12-23-2002, 01:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •