Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Hey Jetboat Guru

  1. #1
    sdpm
    Hey Tony, I just got my Performance Racing Industry Magazine. Is that you on page 73 ? Yellow on top of helmet , purple driving suit with checkers on arms. You might want it for your collection. Talk to you later. Neil

  2. #2
    Her454
    ........More autograph opportunities............... :rollside:

  3. #3
    superdave013
    Tony made PRI hu? To cool

  4. #4
    cole13
    Tony made PRI hu? To cool
    Superdave, I was just looking at your web-site for the first time. Very nice.
    One question though, Is it cheaper to have the fittings re-anodized or to buy new ones? I only ask because mine are all faded and looking to clean it up a bit. Thanks.

  5. #5
    wsuwrhr
    Superdave, I was just looking at your web-site for the first time. Very nice.
    One question though, Is it cheaper to have the fittings re-anodized or to buy new ones? I only ask because mine are all faded and looking to clean it up a bit. Thanks.
    I can answer that.....
    It's definitely cheaper to buy SD's fittings.
    Brian

  6. #6
    Monkey Bung
    Sounds like a GURRRUPPIEEE to me.

  7. #7
    wsuwrhr
    Sounds like a GURRRUPPIEEE to me.
    Just pimpin the good product.....
    I am not scared.
    Brian

  8. #8
    Senior Member
    Join Date
    Feb 2009
    Posts
    4,974
    Scared of what?

  9. #9
    superdave013
    Superdave, I was just looking at your web-site for the first time. Very nice.
    One question though, Is it cheaper to have the fittings re-anodized or to buy new ones? I only ask because mine are all faded and looking to clean it up a bit. Thanks.
    Hey thanks man.
    To answer your question.... Well I don't know. You would have to have them stripped and then re anodized. Before you go to that trouble take a look at the insides of the fittings used on water hoses. I bet they are pretty nasty in there. If so I would replace them over investing good money on a fitting that's already on it's way.

  10. #10
    Senior Member
    Join Date
    Feb 2009
    Posts
    4,974
    Like Superdave said,
    if your fittings are nasty on the outside then they are probably corroded and nasty on the inside. The time and money spent on tearing apart and re-anodizing is going to far exceed the cost of new ones. I had Dave do all my fittings on the Kboat.
    NICE!!!!

Page 1 of 2 12 LastLast

Similar Threads

  1. Guru Looking For Job?
    By Wildchild80 in forum V-Drives
    Replies: 13
    Last Post: 06-03-2006, 10:04 PM
  2. Guru
    By uclahater in forum V-Drives
    Replies: 0
    Last Post: 05-21-2005, 09:15 PM
  3. Guru
    By Kim Hanson in forum Bench Racers
    Replies: 30
    Last Post: 04-20-2005, 07:08 PM
  4. JetBoat GURU knows Props are slower!
    By pops1 in forum Bench Racers
    Replies: 234
    Last Post: 01-05-2005, 06:58 AM
  5. jetboat guru???
    By Blown 472 in forum Bench Racers
    Replies: 17
    Last Post: 01-10-2003, 11:12 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •