I have a 1977 challenger hull 18 1/2 ft. 460BB, and a golden eagle (a.k.a.jacuzzi-y)
it does only 55mph at 5,500 rpm. i need more speed.the inspection plate is to the outside of the transom, i am running a stainless impeller. what are my opptions.
And no, i did not know at the time how bad jacuzzi is!
[This message has been edited by artdra (edited April 19, 2001).]
Go to www.hi-techperformance.com (http://www.hi-techperformance.com) they will help you out . Your pump is doing all it`s going to do . But a new Impeller might help out as it sounds like yours is or might be bad ..E-mail them they can tell you what you need to know ...
American Turbine makes a "jacuzzi energizer" kit. It basically converts the axial flow eagle or yj to a mixed flow pump using amt (dominator?) parts. Check it out at: http://www.americanturbine.com
Click on "Parts & Diagrams"
Eric
[This message has been edited by Eric (edited April 19, 2001).]
I have called american turbine but the say the energizer kit will not add much. have you seen differently?
thanks.
Originally posted by Eric:
American Turbine makes a "jacuzzi energizer" kit. It basically converts the axial flow eagle or yj to a mixed flow pump using amt (dominator?) parts. Check it out at: http://www.americanturbine.com
Click on "Parts & Diagrams"
Eric
[This message has been edited by Eric (edited April 19, 2001).]
The reason it wont add much is because your pump is an insert type pump and add that to your axial flow problem and you have a real all around pump disappointment. I would take it all out and glass in a mixed flow pump like a berkeley or the others. It depends on how much work you want to do to make it go faster. IF you dont mind the work it's cheaper in the long run. Good luck.
chet
Aggresser also makes a energiser kit the the jacuzzi, it comes with the Hiflow 9 vane bowl; I 'm currently doing one right now, parts should arrive tomorrow.Need more info give me a call or e-mail me Jim Brock jbcyclone@aol.com Cyclone speed & marine (818)890-1867 10-7pm
So what your saing is, the bottom of the boat is kindof messing with the intake of the pump since it is a insert pump?
Originally posted by ChetCapoli:
The reason it wont add much is because your pump is an insert type pump and add that to your axial flow problem and you have a real all around pump disappointment. I would take it all out and glass in a mixed flow pump like a berkeley or the others. It depends on how much work you want to do to make it go faster. IF you dont mind the work it's cheaper in the long run. Good luck.
chet
I can't say I've used the "energizer" kit myself but it seems like these kits would make a difference. If you look at the parts list you are basically keeping the suction piece from the yj and using a new (amt or aggressor) bowl, impeller, etc. Of course you could replace the pump completely but that would be a lot more dollars and work. Hopefully Jim will post some results for the aggressor kit.
Eric
Hey artdra,
The problem with your pump is the lack of intake hardware and loading problems you have and always will have. Those energizer kits work great but your pump lacks in both areas, loading and water flow. If your going to spend 1200 bucks on one why not spend the extra 500 or so and buy a used berk somewhere and have it installed? All you will have with the energizer kit is just a done up insert pump anyways(which is not a perf pump) as opposed to a pump setup that will get you 75mph or so right? . That way you can have the best of both worlds. If your going to spend the money on that kit(anything is better than what you have) i would get the aggressor also. Call Ted at C.B.M. (877)Jet-Pump, he'll have the best price on that kit.
I have installed the american turbine kit on my boat and am very happy with it.I do not have any loading problems have put a top loader grate on it.the boat will run 65-70.I put the kit on about 10 years ago bought it from adm boatworks.The previous pump was the golden eagle jacuzzi.Instantly worked better.Will offer you a ride.
Posting Permissions
Reply With Quote