TPC Racing Does it again!

[skeepwerkzaz]

Well Ty @ TPC has done it yet again....He has taken my barely serviceable holley 660 center-squirters and turned them both into pieces of art. They really do speak for themselves....Here is a shot of my engine before [img]http://www.***boat.com/image_center/data/521/485engine_rt-med.jpg[/img]
here is a shot of the "carbs" going to the powdercoater... [img]http://www.***boat.com/image_center/data/521/485before.bmp[/img]
and here are the "same" ones back on the engine.... [img]http://www.***boat.com/image_center/data/521/485left_side1-med.jpg[/img]
another angle.. [img]http://www.***boat.com/image_center/data/521/485good_overall-med.jpg[/img]
a closer look.. [img]http://www.***boat.com/image_center/data/521/485good_closeup-med.jpg[/img]
just a few more lines to run and vvrroom vrrooom. [img]http://www.***boat.com/image_center/data/521/485right_side-med.jpg[/img]
As you can see, Ty does awesome work. When I opened the boxes, i'm not sure if it was the excitement of seeing my carbs or the powdercoating fumes, but I felt euphoric. Not quite to the point of lakesonly eek! , but I definately got lightheaded. Thanks for the amazing work Ty, thanks for the gift Froggy You really didn't have too.... but it 's killer that you did. I'll get you back sometime. But for now I owe you both airplane rides, boat rides and da beers. And as for the rest of you....see you at CBBB.
Skeep
[ August 04, 2003, 11:29 PM: Message edited by: skeepwerkzaz ]

[LakesOnly]

Here ya go:
skeepwerkzaz:
(Edited by LO) LO
[ August 04, 2003, 11:35 PM: Message edited by: LakesOnly ]

[skeepwerkzaz]

Thanks Lakes....
What did I do wrong?
I also went back and changed that repeat close-up.
[ August 04, 2003, 11:17 PM: Message edited by: skeepwerkzaz ]

[LakesOnly]

skeepwerkzaz:
Thanks Lakes....
What did I do wrong?
I also went back and changed that repeat close-up. The backslash has to be inside the second set of brackets, a la:
THIS: blah blah blah
NOT THIS: [img]blah blah blah/[img]
You dislexic fool
LO

[skeepwerkzaz]

Thanks...

[Hotcrusader76]

Looks great Clay! Don't forget to plumb the otherside as well or else ya might be lean on the top-end
So am I final tuning this pig for ya at the CBBB or hopefully you're hauling in confidence...LOL
My boat will be wet Wednesday for the first time in 12 months since last CBBB, which I busted a valve spring 3 days before the event. Tomorrow I will break the camshaft in and then battle the chore of putting the inner springs back in
There's nothing like replacing springs on a pair of heads when they're installed...yack!

[LakesOnly]

skeepwerkzaz:
Thanks... No Prob....nice carbs, by the way.
LO

[skeepwerkzaz]

Ty...Still trying to figure out the plumbing, I am not quite sure exactly what I am going to do, but I'll have it done on Wed. Mine has already been wet, and everything works as advertised, so there shouldn't be too much drama. I got the timing(valve)sorted out and am ready to rumble. I had the intake off, and I could see the cam is broken in, so ya know, I have that going for me. See you soon and thanks again..
Clay

[Hotcrusader76]

I will send ya some pics on ideas for mounting those lines.
I just finished mounting mine yesterday (Dual 650 double pumpers hybrids with 850 baseplates and 1850 bowls similar to your set-up). The difference is that mine have 08AN lines/fittings and little to no space for plumbing, but nonetheless it came out looking trick...
Check your email tomorrow.
~Ty