Page 1 of 4 1234 LastLast
Results 1 to 10 of 31

Thread: Rail Kit....

  1. #1
    Senior Member
    Join Date
    Feb 2009
    Posts
    3,387
    dimentions of a BBC rail kit or any type of drawings?
    any info will help out bitchenly!
    P.S. Been drinkin', sorry!

  2. #2
    Senior Member
    Join Date
    Feb 2009
    Posts
    3,387
    8 views,...come on guys?

  3. #3
    BrendellaJet
    They are all different. If you have some old mounts(4 point) use those as a pattern. Or do it the hard way like I did and make em yourself. I started with some masonite and when I was satisfied with the fit I transfered it to aluminum. Lots of work. Save some time and buy Duanes kit... Its a good deal. Fit it your self...measure twice, cut once.

  4. #4
    Senior Member
    Join Date
    Feb 2009
    Posts
    3,387
    maybe i should have gotten a little deeper in discussion,... Im being a lazy ****! and besides masonite is used for skating a ramps! basically i am looking for some #'s on the bolt pattern on the block!...sorry for not being clear as crystal, but remember....im ****oed!
    Thanks again!
    Todd

  5. #5
    Duane HTP
    "basically i am looking for some #'s on the bolt pattern on the block!..."
    What is it that you are asking here???? We don't understand your question??

  6. #6
    wsuwrhr
    maybe i should have gotten a little deeper in discussion,... Im being a lazy ****! and besides masonite is used for skating a ramps! basically i am looking for some #'s on the bolt pattern on the block!...sorry for not being clear as crystal, but remember....im ****oed!
    Thanks again!
    Todd
    Contact the guy who knows how to build this stuff.

  7. #7
    bottom feeder
    Is this what you need??
    http://www.***boat.com/image_center/...evy_plates.jpg
    I have most all the blocks :idea: What wsuwrhr said

  8. #8
    wsuwrhr
    Is this what you need??
    http://www.***boat.com/image_center/...evy_plates.jpg
    I have most all the blocks :idea: What wsuwrhr said
    Got a magnifying glass?
    That print is worthless.

  9. #9
    LGCDEVIL
    I've got a piece of 3/8" plate with that I traced the plates on. Center punched the holes. You are welcome to it. Just replace the plate with another patern after you have made your plates.

  10. #10
    edog_103
    Is this what you need??
    http://www.***boat.com/image_center/...evy_plates.jpg
    I have most all the blocks :idea: What wsuwrhr said
    I am helping Todd out on this. What we are going to do is take these hole locations and make a pattern to be cut on the Laser. We can come up with some pretty creative designs. Can you attach this picture as a DWG file or DXF?

Page 1 of 4 1234 LastLast

Similar Threads

  1. Rail kit
    By Bigern in forum Jet Boats
    Replies: 38
    Last Post: 04-08-2007, 09:30 PM
  2. looking for rail kit
    By akjet in forum Jet Boats
    Replies: 6
    Last Post: 11-06-2005, 09:33 PM
  3. Rub Rail...Help
    By Powerquestboy in forum Sandbar
    Replies: 4
    Last Post: 02-20-2004, 08:01 PM
  4. New Bow Rail
    By e-ticket in forum V-Drives
    Replies: 8
    Last Post: 05-06-2002, 03:02 PM
  5. RUB RAIL
    By regattajboat in forum Bench Racers
    Replies: 5
    Last Post: 03-22-2002, 05:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •