Results 1 to 10 of 10

Thread: Percision props

  1. #1
    FlatRat
    Are these props good,bad or ugly.Also,I tried a 12"x15" two blade Hill on my 18'BBC Sanger with 17 over and got 6,800 rpm's.What could I expect with the 11 3/4 x 16 two blade Percision.Thanks.

  2. #2
    Sangster
    What rpm is your motor setup to run?? The smaller prop will give you more rpm...It's hard to say if it will work or how well it will work..Again, it might be the prop you need, but if your setup isn't right, the boat will not be able do what it's supposed to do...If ya know what I mean.... wink wink wink

  3. #3
    058
    That extra inch of blade pitch is almost like adding 10% gear to the v-drive. The 11 3/4 x 16 will load the engine more.

  4. #4
    superdave013
    They are great props. Made by the late Tom Black.
    If you have a Casale quick change then you are not running 17% over. Maybe 15 or 18

  5. #5
    FlatRat
    O.k.,the motor is about maxed out.It is set up to run from 6,500 to an occasional 7,000 but not a sustained 7,000.It's a .030 over 454,990 heads,2.25 intake with 1.88 exhaust,294 solid cam.Team G manifold and 850 DP. The gear box is a Hallcraft.The gears had a 17 stamped on them.So when you say "it will load the engine more" you mean it not wind up as much?I'm fairly new at this so please " beer" with me.Thanks

  6. #6
    superdave013
    FlatRat:
    O.k.,the motor is about maxed out.It is set up to run from 6,500 to an occasional 7,000 but not a sustained 7,000.It's a .030 over 454,990 heads,2.25 intake with 1.88 exhaust,294 solid cam.Team G manifold and 850 DP. The gear box is a Hallcraft.The gears had a 17 stamped on them.So when you say "it will load the engine more" you mean it not wind up as much?I'm fairly new at this so please " beer" with me.ThanksFlatRat, I think that prop will work out for you. It should drop your RPM a little. If it still is turning more RPM then you want then you will need to do a gear swap. Just so you know, Memkens v drives (V Drive Tom) is still making parts for your Hallcraft box. I'm sure he can get you a higher gear ratio if you need it.

  7. #7
    FlatRat
    Thanks for the info,but all that typeing and not much check writing cost me.I fargin snooozed on the deal.I'll keep searchin, the winters are long up here in Montana.I've got 6 months before the ice is melted off the water.Hhmm.. I wonder if I could put runners on the flat.

  8. #8
    DUCKY
    FLATRAT,
    My brother has a few two blades for sale, I think one of which is a 11 3/4" x 16 precision. I think he wanted $250 for them. Give him a call at (602) 992-3509 his name is Chad.

  9. #9
    FlatRat
    Ducky,thanks but those are the ones I snoozed on.I will keep searchin.I would try a 12x15 or a 11 1/2x16.Anybody out there?

  10. #10
    DUCKY
    Sorry,
    I thought he still had them.

Similar Threads

  1. Props Props Props for sale
    By IDRPSTF in forum Parts 4 Sale
    Replies: 2
    Last Post: 11-10-2007, 09:32 AM
  2. Quick thank you to Scott at Percision Boatwerx...
    By One Particular Harbor in forum Sandbar
    Replies: 3
    Last Post: 04-23-2006, 08:54 PM
  3. Props???
    By Waldo in forum Out Drive
    Replies: 3
    Last Post: 06-04-2004, 09:07 AM
  4. Props
    By moneypit in forum Sandbar
    Replies: 8
    Last Post: 05-04-2004, 04:43 PM
  5. Props
    By I_C_E_Y in forum V-Drives
    Replies: 16
    Last Post: 09-19-2002, 10:29 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •