Page 1 of 3 123 LastLast
Results 1 to 10 of 23

Thread: Good Pictures of my Carbon Fiber Covers

  1. #1
    Kurtis500
    Hope you enjoy, I've spent LOTS AND LOTS of time on this. I finally got around to polishing one of these and WOW what a difference it makes. Only 5 minutes of extra work does wonders.
    [img]http://free.***boat.net/cgi-bin/imageFolio.cgi?action=view&link=Forum_Graphic_Depo t&image=PB270019.JPG[/img]
    [img]http://free.***boat.net/cgi-bin/imageFolio.cgi?action=view&link=Forum_Graphic_Depo t&image=cover.JPG&img=&tt=[/img]
    Figures. I need help with this, would someone edit my post and let me know where I'm getting this wrong to post an image. Heres the links at least
    http://free.***boat.net/cgi-bin/imag...r.JPG&img=&tt=
    http://free.***boat.net/cgi-bin/imag...9.JPG&img=&tt=
    [ November 27, 2002, 09:43 PM: Message edited by: Kurtis500 ]

  2. #2
    Sangster
    [img]http://free.***boat.net/gallery/Forum_Graphic_Depot/PB270019.JPG[/img]

  3. #3
    Sangster
    [img]http://free.***boat.net/gallery/Forum_Graphic_Depot/cover.JPG[/img]

  4. #4
    Omega21
    Kurtis-
    Nice stuff! Do you offer classes? :-) I'm not out to build valve covers, but I do have ideas on other things I'd like to build for my boat!
    Todd

  5. #5
    DAVE94LIGHTNING
    Sweet!!!!!! Those would look perfect on my motor.
    Quick question. What spark plug wires do you reccomend? I have tried MSD and MOROSO wires but my problem is that the round "caps" do not seal the holes in the valve covers tightly. Any ideas?
    Thanks.
    [ November 28, 2002, 01:59 AM: Message edited by: DAVE94LIGHTNING ]

  6. #6
    DansBlown73Nordic
    Those look great!!!Nice Job......

  7. #7
    GofastRacer
    Kurtis, that is totally awesome!!! eek! Are you going to make some tall BBC's???, you have one set sold already!!!... wink

  8. #8
    Kurtis500
    THANKS EVERYONE!! Unfortunate part about it is that this particular cover is no-good. I experimented with catalyst and the rail warped. I can use it on my motor but I wouldnt sell it to anyone.

  9. #9
    Kurtis500
    Omega21, I'm no expert on some of this stuff, but i feel very confident about the area I am working in. It all depends on what you want to make. Some stuff is easier and layable like fiberglass and other things need a little special equipment. If you let me know what you want to make I can make suggestions that may at least help.

  10. #10
    Kurtis500
    DAVE94LIGHTNING:
    Sweet!!!!!! Those would look perfect on my motor.
    Quick question. What spark plug wires do you reccomend? I have tried MSD and MOROSO wires but my problem is that the round "caps" do not seal the holes in the valve covers tightly. Any ideas?
    Thanks.I havent ever used the rubber boots that fit on the valve cover. I have always just ran the wire through the hole. I have to be careful and NOT pull the plugs if the motor may have been recently wet. If the tubes are pulled out, water that is pooled up will fall straight in the cylinder and right into the oil pan. I usually blow out the spark plug tubes before I unscrew them. Do you have the PAW catalog? There are a couple of places to try that have really good classified sections frequented by 392 people
    www.powerplayhemi.com check the swap meet and/or leave an ad
    www.nitronic.com You'll find most 392 stuff here is AA or similar, but post an add, most guys have the stuff and dont bother trying to sell it. I actually have a set of the rails that go on the valve covers somewhere around here. They push down on the washers that are on the tubes and seal them up, along with hide the wires.

Page 1 of 3 123 LastLast

Similar Threads

  1. Carbon fiber valve covers
    By 469 the coyote in forum Parts 4 Sale
    Replies: 7
    Last Post: 11-04-2007, 10:42 AM
  2. Carbon Fiber Valve Covers
    By 76 Bonneville in forum Jet Boats
    Replies: 25
    Last Post: 08-06-2007, 12:27 AM
  3. New carbon fiber engine covers
    By Phat Matt in forum Sandbar
    Replies: 25
    Last Post: 02-25-2006, 03:17 PM
  4. Carbon fiber valve covers
    By Omega21 in forum Jet Boats
    Replies: 8
    Last Post: 06-17-2003, 09:13 AM
  5. Carbon Fiber Valve Covers
    By P-Money in forum Sandbar
    Replies: 18
    Last Post: 10-17-2002, 10:23 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •