Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: Puke Tank Set-up

  1. #1
    Hotcrusader76
    This has got to be the most expensive looking Puke Tank configuration ever, no? Those AN fittings alone are worth over a hundred bucks.
    Looks bitchen' though!
    [img]http://www.***boat.com/image_center/data/500/350Headers_Install_3-med.jpg[/img]

  2. #2
    skeepwerkzaz
    Those headers must make taking the valve covers off a BIIIIOOOOOTCH. Those look like -16 fittings. Mucho $$$ Have you looked into the vacuum pump set-up yet?

  3. #3
    Hotcrusader76
    Damn Clay....as much as you mention it I might even consider it...LMAO.
    E-mail me your digits (Cell#)
    Are you going to AVI Casino CBB?
    ~Ty

  4. #4
    Senior Member
    Join Date
    Feb 2009
    Posts
    1,542
    Here is my Puke tank set up:
    [img]http://www.***boat.com/image_center/data/520/41IMG_1664-med.JPG[/img]

  5. #5
    Thunderbutt
    ssmike:
    Here is my Puke tank set up:
    [img]http://www.***boat.com/image_center/data/520/41IMG_1664-med.JPG[/img] Shoudn't the tank be below the valve covers like ssmike has his. Thats the way mine is.

  6. #6
    Froggystyle
    I kind of like it when they drain back into the valve covers, and I have never had a blow-by problem big enough to warrant any other configuration. I actually put the bungs on the bottom of the tank, and vent on the top.

  7. #7
    Froggystyle
    skeepwerkzaz:
    Those headers must make taking the valve covers off a BIIIIOOOOOTCH. Those look like -16 fittings. Mucho $$$ Have you looked into the vacuum pump set-up yet? Those are the same ones I had on the picklefork. Not really all that bad. They just slide down underneath the header.
    I think Basset calls them twisties.

  8. #8
    LakesOnly
    Hotcrusader76:
    This has got to be the most expensive looking Puke Tank configuration ever, no? Those AN fittings alone are worth over a hundred bucks.
    Looks bitchen' though!
    [img]http://www.***boat.com/image_center/data/500/350Headers_Install_3-med.jpg[/img]Where have I seen that set-up.....oh yeah! It's MINE! Even valve covers were custom fab'd (okay, modified) so that the breather system snakes around the headers.
    Incidentally, I have to agree that those old Sanderson headers wrap a little tightly around the valve covers, and some may find it inconvenient from a maintenance standpoint. Never-the-less, I elected to use them as a styling cue. They're different...I like that.
    LO
    [ June 19, 2003, 10:50 PM: Message edited by: LakesOnly ]

  9. #9
    burbanite
    Thunderbutt:
    Shoudn't the tank be below the valve covers like ssmike has his. Thats the way mine is. I have mine mounted higher as well. I built it with stepped internal baffles and a drain on the bottom, inlets on the sides, dash 12 lines. Seemed to do the trick...

  10. #10
    Thunderbutt
    Let me ask this. What is the puke tank for? Why do we have it?

Page 1 of 2 12 LastLast

Similar Threads

  1. need puke tank
    By craig moss in forum Parts 4 Sale
    Replies: 0
    Last Post: 12-15-2007, 08:15 AM
  2. Puke Tank Kit
    By wet77 in forum Parts 4 Sale
    Replies: 10
    Last Post: 11-24-2007, 03:50 PM
  3. Need A Puke Tank!
    By N/AZZ502 in forum Jet Boats
    Replies: 5
    Last Post: 08-29-2007, 03:30 PM
  4. Looking for a puke tank
    By Taylorman in forum Jet Boats
    Replies: 3
    Last Post: 08-09-2005, 01:04 PM
  5. Puke Tank
    By e-ticket in forum V-Drives
    Replies: 12
    Last Post: 11-05-2003, 06:31 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •